2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)

3. REMOVE FRONT BUMPER LOWER COVER
  1. Remove the clip, 5 bolts and front bumper lower cover.


4. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 4 bolts and No. 1 engine under cover.


5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A218364
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A245857E01

    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Vent Plug
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug


6. REMOVE FRONT FENDER APRON SEAL RH
  1. Using a clip remover, remove the 5 clips and front fender apron seal RH.


7. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH
  1. Using a clip remover, remove the 4 clips and front No. 1 fender apron to frame seal RH.


8. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


9. REMOVE FRONT HEATER BRACKET (for Cold Area Specification Vehicles)

  1. A223523
    Remove the 2 bolts and front heater bracket.


10. REMOVE FAN AND GENERATOR V BELT
  1. Using the pulley set bolt of the tensioner, rotate the tensioner pulley clockwise to loosen the belt tension. Then remove the V belt.


11. REMOVE NO. 1 AIR CLEANER HOSE

  1. A223211
    Loosen the 2 hose clamps and remove the No. 1 air cleaner hose.


12. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

A246272E02
  1. except Cold Area Specification Vehicles:
    Detach the 2 clamps and disconnect the mass air flow meter connector.

    Text in Illustration 
    *A
    except Cold Area Specification Vehicles
    *B
    for Cold Area Specification Vehicles

  1. for Cold Area Specification Vehicles:
    Detach the 3 clamps and disconnect the mass air flow meter connector.

  1. Detach the 4 clamps and remove the air cleaner cap sub-assembly.


13. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

14. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

  1. A223214
    Remove the 3 bolts and air cleaner case sub-assembly.


15. DISCONNECT HEATER HOSE AND PIPE (w/ Rear Air Conditioning System)

  1. A246261
    Slide the 3 clamps, disconnect the 3 heater hoses from the heater pipe.

  1. Remove the bolt and disconnect the heater hose and pipe.


16. REMOVE HEATER HOSE (w/o Rear Air Conditioning System)

  1. A246262
    Slide the 2 clamps and remove the heater hose from the heater pipe.


17. REMOVE NO. 1 AIR HOSE

  1. A218373
    Loosen the 2 clamps.

  1. Remove the No. 1 air hose from the inlet pipe and intercooler.


18. REMOVE COMPRESSOR OUTLET ELBOW

  1. A223215
    Detach the 3 wire harness clamps.

  1. Remove the bolt and wire harness bracket.

  1. A220719
    Loosen the hose clamp and remove the 2 bolts and compressor outlet elbow.


19. REMOVE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (for Cold Area Specification Vehicles)
  1. Disconnect the viscous heater connector.

  1. A223522
    Disconnect the water by-pass hose and water hose.

  1. A223524
    Remove the 2 bolts and viscous heater with magnet clutch.


20. REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)

  1. A223525
    Remove the 4 bolts and No. 1 viscous heater bracket.


21. DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

  1. A223526
    Disconnect the compressor connector.

  1. Remove the 4 bolts and disconnect the cooler compressor.


22. REMOVE GENERATOR ASSEMBLY

  1. A222880
    Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the generator wire.

  1. Remove the 2 bolts and generator.


23. REMOVE GENERATOR BRACKET

  1. A239369
    Remove the bolt and generator bracket.


24. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

  1. A244867
    Remove the 5 bolts and No. 1 compressor mounting bracket.


25. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A244588
    Remove the 2 bolts and No. 2 exhaust manifold heat insulator from the turbine outlet elbow.


26. REMOVE TURBINE OUTLET ELBOW STAY

  1. A244591
    Remove the 2 bolts and turbine outlet elbow stay from the No. 2 turbine outlet elbow and cylinder block sub-assembly.


27. REMOVE NO. 2 TURBINE OUTLET ELBOW

  1. A244592
    Remove the 3 nuts, No. 2 turbine outlet elbow and gasket from the turbine outlet elbow.


28. DISCONNECT NO. 1 FUEL PIPE

  1. A246265
    Remove the 2 bolts, union bolt and gasket.
    Text in Illustration 
    V100136
    Union Bolt

  1. Disconnect the No. 1 fuel pipe from the turbine outlet elbow.


29. REMOVE FUEL PIPE CLAMP

  1. A244599
    Remove the bolt and fuel pipe clamp from the turbine outlet elbow.


30. REMOVE NO. 11 WATER BY-PASS HOSE

  1. A244593
    Disconnect the exhaust fuel addition injector connector.

  1. Slide the 2 clamps and remove the No. 11 water by-pass hose from the turbine outlet elbow.


31. REMOVE TURBINE OUTLET ELBOW

  1. A245472E01
    Remove the union bolt and gasket from the turbine outlet elbow.
    Text in Illustration 
    *1
    No. 4 Water By-pass Pipe
    *2
    No. 12 Water By-pass Hose
    *3
    Turbine Outlet Elbow
    *4
    Gasket
    *5
    Union Bolt

  1. Slide the clamp and remove the No. 4 water by-pass pipe from the No. 12 water by-pass hose.

  1. Remove the 3 nuts, turbine outlet elbow and gasket from the turbocharger sub-assembly.


32. DISCONNECT VENTILATION PIPE

  1. A308001
    Type A
    Slide the 2 clamps and disconnect the No. 3 turbo water hose and No. 4 turbo water hose from the ventilation pipe.

  1. A308002E01
    Remove the bolt and disconnect the 2 ventilation hoses and ventilation pipe from the cylinder head sub-assembly.
    Text in Illustration 
    *A
    Type A
    *B
    Type B


33. REMOVE NO. 1 TURBO INSULATOR

  1. A244589
    Remove the 2 bolts and No. 1 turbo insulator from the turbocharger sub-assembly.


34. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Remove the 2 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.


35. DISCONNECT ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A245676
    Remove the bolt.

  1. Disconnect the engine oil level dipstick guide from the cylinder block sub-assembly.


36. DISCONNECT NO. 1 TURBO WATER HOSE

  1. A309155E01
    Slide the 2 clamps and disconnect the No. 1 turbo water hose from the No. 2 water by-pass pipe.
    Text in Illustration 
    *A
    Type A
    *B
    Type B
    *1
    No. 1 Turbo Water Hose
    *2
    No. 3 Turbo Water Hose

  1. Type B
    Slide the clamp and disconnect the No. 3 turbo water hose from the compressor inlet elbow.


37. REMOVE NO. 3 TURBO WATER HOSE
  1. Slide the clamp and remove the No. 3 turbo water hose from the No. 2 water by-pass pipe.


38. REMOVE TURBOCHARGER STAY

  1. A220726
    Remove the 2 bolts, nut and turbocharger stay from the turbocharger sub-assembly and cylinder block.


39. REMOVE WIRE HARNESS CLAMP BRACKET

  1. A245675
    Remove the bolt and wire harness clamp bracket from the cylinder block.


40. REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

  1. A220727E01
    Remove the 2 bolts, 2 nuts, union bolt, turbo oil inlet pipe sub-assembly and 3 gaskets.

    NOTICE:
    Do not loosen the nut labeled A in the illustration.


41. REMOVE EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

  1. A244596
    Remove the 8 nuts and 8 plate washers from the exhaust manifold with turbocharger sub-assembly.

  1. Remove the exhaust manifold with turbocharger sub-assembly and gasket.


42. REMOVE TURBOCHARGER SUB-ASSEMBLY

  1. A220729
    Remove the 3 nuts, turbocharger sub-assembly and gasket.


43. REMOVE COMPRESSOR INLET ELBOW

  1. A308005E01
    Remove the 2 nuts, compressor inlet elbow and gasket from turbocharger sub-assembly.
    Text in Illustration 
    *A
    Type A
    *B
    Type B
    *1
    No. 4 Turbo Water Hose
    *2
    No. 3 Turbo Water Hose

  1. Type A
    Slide the clamp and remove the No. 4 turbo water hose from the compressor inlet elbow.

  1. Type B
    Slide the clamp and remove the No. 3 turbo water hose from the compressor inlet elbow.


44. REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

  1. A244598
    Remove the 2 nuts, bolt, No. 1 turbo water pipe sub-assembly and gasket from the turbocharger sub-assembly.

← SYSTEM DESCRIPTION (from Aug 2014)REMOVAL (from Aug 2014) →