2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2013


1. REMOVE TAILPIPE ASSEMBLY

  1. A226972E01
    Remove the 2 bolts and disconnect the tailpipe from the exhaust pipe support.
    Text in Illustration 
    *A
    for 3 Door
    *B
    for 5 Door

  1. Remove the gasket.


2. REMOVE CENTER EXHAUST PIPE ASSEMBLY

  1. A245475
    for 3 Door:
    Remove the 2 bolts and 2 compression springs, and then disconnect the center exhaust pipe from the 2 exhaust pipe supports.

  1. A245482
    for 5 Door:

    1. Remove the 2 bolts and 2 compression springs, and then disconnect the center exhaust pipe from the 3 exhaust pipe supports.

    2. A244585
      Remove the 2 bolts and exhaust pipe damper.

    3. Remove the nuts and No. 1 exhaust pipe heat insulator.

  1. Remove the gasket.


3. REMOVE FRONT SUSPENSION MEMBER BRACKET LH (for Manual Transmission)

C215587
  1. Remove the 4 bolts and front suspension member bracket LH.


4. REMOVE FRONT SUSPENSION MEMBER BRACKET RH (for Manual Transmission)

C215588
  1. Remove the 4 bolts and front suspension member bracket RH.


5. REMOVE FRONT SUSPENSION MEMBER BRACKET RH (for Automatic Transmission)

  1. C214435
    Remove the 8 bolts, front bracket suspension member LH and front bracket suspension member RH.


6. SUPPORT TRANSMISSION AND TRANSFER ASSEMBLY
  1. Support the transmission and transfer with a transmission jack.

    NOTICE:
    For safety reasons, install the No. 3 frame crossmember after removing the front exhaust pipe.


7. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY (for Automatic Transmission)

  1. C171489
    Remove the 4 bolts of the rear engine mounting insulator.

  1. C214464
    Remove the 4 nuts, 4 bolts and frame crossmember.


8. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY (for Manual Transmission)
  1. Support the rear side of the transmission with a support stand.

  1. C215589
    Remove the 4 bolts from the No. 3 frame crossmember sub-assembly.

  1. C215614
    Remove the 4 nuts, 4 bolts and No. 3 frame crossmember sub-assembly.


9. REMOVE NO. 2 EXHAUST PIPE SUPPORT BRACKET

  1. A246252
    Remove the 2 bolts and No. 2 exhaust pipe support bracket from the body.


10. REMOVE NO. 3 EXHAUST PIPE SUPPORT BRACKET

  1. A246251
    Remove the 2 bolts and No. 3 exhaust pipe support bracket from the No. 3 frame crossmember.


11. REMOVE AIR FUEL RATIO SENSOR

  1. A239603
    Disconnect the air fuel ratio sensor connector and detach the clamp.

  1. A239604E01
    Using SST, remove the air fuel ratio sensor from the front exhaust pipe.
    SST
    09224-00010  


12. REMOVE FRONT EXHAUST PIPE ASSEMBLY

  1. A244604
    Disconnect the exhaust gas temperature sensor connector.

  1. A244605
    Disconnect the No. 2 exhaust gas temperature sensor connector.

  1. A244606
    Disconnect the No. 3 exhaust gas temperature sensor connector.

  1. A244583
    Disconnect the No. 6 exhaust pipe air hose from the front exhaust pipe.

  1. A244582
    Disconnect the No. 7 exhaust pipe air hose from the front exhaust pipe.

  1. A244581
    Remove the 2 exhaust pipe supports.

    HINT:
    Remove the exhaust pipe supports before removing the No. 3 frame crossmember.

  1. A244580
    Remove the 3 nuts and front exhaust pipe.

  1. Remove the gasket.


13. REMOVE EXHAUST GAS TEMPERATURE SENSOR

A245476

NOTICE:
If the sensor is dropped, replace it with a new one.

  1. Using a 14 mm union nut wrench, remove the exhaust gas temperature sensor.


14. REMOVE NO. 2 EXHAUST GAS TEMPERATURE SENSOR

A245477E02

NOTICE:
If the sensor is dropped, replace it with a new one.

  1. Using a 14 mm union nut wrench, remove the No. 2 exhaust gas temperature sensor.

    Text in Illustration 
    *A
    for Automatic Transmission
    *B
    for Manual Transmission


15. REMOVE NO. 3 EXHAUST GAS TEMPERATURE SENSOR

A245478

NOTICE:
If the sensor is dropped, replace it with a new one.

  1. Detach the sensor wire harness.

  1. Using a 14 mm union nut wrench, remove the No. 3 exhaust gas temperature sensor.


16. REMOVE NO. 3 WIRING HARNESS CLAMP BRACKET

  1. A244587
    Remove the bolt and No. 3 wiring harness clamp bracket.


17. REMOVE EXHAUST PIPE CLAMP SUB-ASSEMBLY

  1. A244586
    Remove the bolt and exhaust pipe clamp.


18. REMOVE MONOLITHIC CONVERTER PROTECTOR

  1. A244601
    Remove the 4 bolts and 4 nuts.

  1. A244602E01
    Remove the upper monolithic converter protector and lower monolithic converter protector.
    Text in Illustration 
    *1
    Upper Monolithic Converter Protector
    *2
    Lower Monolithic Converter Protector


19. REMOVE CONVERTER PROTECTOR STAY

  1. A244603E01
    Remove the 2 No. 1 converter protector stays and 2 No. 2 converter protector stays.
    Text in Illustration 
    *1
    No. 1 Converter Protector Stay
    *2
    No. 2 Converter Protector Stay

← COMPONENTS (from Aug 2013)INSTALLATION (from Aug 2013) →