2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT BUMPER LOWER COVER
  1. Remove the clip, 5 bolts and front bumper lower cover.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and No. 1 engine under cover.


4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A218364
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A218365E01

    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Vent Plug
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug


5. REMOVE FRONT EXHAUST PIPE ASSEMBLY

  1. A226973E01
    Remove the 3 nuts and front exhaust pipe.
    Text in Illustration 
    *A
    w/ EGR Cooler
    *B
    w/o EGR Cooler

  1. Remove the gasket.


6. REMOVE FRONT FENDER APRON SEAL RH
  1. Using a clip remover, remove the 4 clips and front fender apron seal RH.


7. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH
  1. Using a clip remover, remove the 5 clips and front No. 1 fender apron to frame seal RH.


8. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


9. REMOVE FRONT HEATER BRACKET (for Cold Area Specification Vehicles)

  1. A223523
    Remove the 2 bolts and front heater bracket.


10. REMOVE FAN AND GENERATOR V BELT
  1. Using the pulley set bolt of the tensioner, rotate the tensioner pulley clockwise to loosen the belt tension. Then remove the V belt.


11. REMOVE NO. 1 AIR CLEANER HOSE

  1. A223211
    Loosen the 2 hose clamps and remove the No. 1 air cleaner hose.


12. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

A246272E02
  1. except Cold Area Specification Vehicles:
    Detach the 2 clamps and disconnect the mass air flow meter connector.

    Text in Illustration 
    *A
    except Cold Area Specification Vehicles
    *B
    for Cold Area Specification Vehicles

  1. for Cold Area Specification Vehicles:
    Detach the 3 clamps and disconnect the mass air flow meter connector.

  1. Detach the 4 clamps and remove the air cleaner cap sub-assembly.


13. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

14. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

  1. A223214
    Remove the 3 bolts and air cleaner case sub-assembly.


15. REMOVE NO. 1 AIR HOSE

  1. A218373
    Loosen the 2 clamps.

  1. Remove the No. 1 air hose from the inlet pipe and intercooler.


16. REMOVE COMPRESSOR OUTLET ELBOW

  1. A223215
    Detach the 3 wire harness clamps.

  1. Remove the bolt and wire harness bracket.

  1. A220719
    Loosen the hose clamp and remove the 2 bolts and compressor outlet elbow.


17. REMOVE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (for Cold Area Specification Vehicles)
  1. Disconnect the viscous heater connector.

  1. A223522
    Disconnect the water by-pass hose and water hose.

  1. A223524
    Remove the 2 bolts and viscous heater with magnet clutch.


18. REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)

  1. A223525
    Remove the 4 bolts and No. 1 viscous heater bracket.


19. DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

  1. A223526
    Disconnect the compressor connector.

  1. Remove the 4 bolts and disconnect the cooler compressor.


20. REMOVE GENERATOR ASSEMBLY

  1. A222880
    Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the generator wire.

  1. Remove the 2 bolts and generator.


21. REMOVE GENERATOR BRACKET

  1. A224117
    Remove the bolt and generator bracket.


22. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

  1. A224118
    Remove the 5 bolts and No. 1 compressor mounting bracket.


23. REMOVE VENTILATION PIPE

  1. A308001
    Type A
    Slide the 2 clamps and disconnect the No. 3 turbo water hose and No. 4 turbo water hose from the ventilation pipe.

  1. A308002E01
    Remove the bolt and disconnect the 2 ventilation hoses and ventilation pipe from the cylinder head sub-assembly.
    Text in Illustration 
    *A
    Type A
    *B
    Type B


24. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the engine oil level dipstick.

  1. A220721
    Remove the 2 bolts and engine oil level dipstick guide from the cylinder block sub-assembly.

  1. Remove the O-ring from the engine oil level dipstick guide.


25. REMOVE COMPRESSOR INLET ELBOW

  1. A223216
    Detach the 3 wire harness clamps.

  1. Remove the bolt and wire harness bracket from the water inlet.

  1. Disconnect the 2 connectors and detach the wire harness clamp.

    A309156E01

    Text in Illustration 
    *A
    Type A
    *B
    Type B

  1. Slide the clamp and disconnect the No. 2 turbo water hose from the No. 1 turbo water hose sub-assembly.

  1. Slide the clamp and disconnect the No. 3 turbo water hose from the No. 2 water by-pass pipe.

  1. Remove the 2 nuts, compressor inlet elbow and gasket from the turbocharger sub-assembly.


26. REMOVE NO. 1 TURBO INSULATOR

  1. A220723
    Remove the 2 bolts and No. 1 turbo insulator from the turbocharger sub-assembly.


27. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Remove the bolt and No. 1 exhaust manifold heat insulator from the exhaust manifold.


28. DISCONNECT NO. 1 TURBO WATER HOSE

  1. A220724
    Disconnect the No. 1 turbo water hose from the No. 1 turbo water pipe sub-assembly.


29. REMOVE TURBINE OUTLET ELBOW

  1. A220725
    Remove the 3 nuts, turbine outlet elbow and gasket from the turbocharger sub-assembly.


30. REMOVE TURBOCHARGER STAY

  1. A220726
    Remove the 2 bolts, nut and turbocharger stay from the turbocharger sub-assembly and cylinder block sub-assembly.


31. REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

  1. A220727E01
    Remove the 2 bolts, 2 nuts, union bolt, turbo oil inlet pipe sub-assembly and 3 gaskets from the turbocharger sub-assembly and cylinder block sub-assembly.

    NOTICE:
    Do not loosen the nut labeled A in the illustration.


32. REMOVE EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

  1. A220728
    Remove the 8 nuts, 8 plate washers and 8 collars from the exhaust manifold with turbocharger sub-assembly.

  1. Remove the exhaust manifold with turbocharger and gasket.


33. REMOVE TURBOCHARGER SUB-ASSEMBLY

  1. A220729
    Remove the 3 nuts, turbocharger sub-assembly and gasket from the exhaust manifold.


34. REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

  1. A220730
    Remove the 2 nuts, bolt, No. 1 turbo water pipe sub-assembly and gasket from the turbocharger sub-assembly.

← REMOVAL (Aug 2013 – Jul 2014)INSPECTION (from Aug 2013) →