B279A Theft Deterrent System Communication Line High Fixation
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
If the communication line (EFIO-IMI) to the ID code box is stuck on HI output, the ECM stores this DTC.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B279A |
The communication line (EFIO-IMI) between the ECM and the ID code box (immobiliser code ECU) is stuck on HI output. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the ID code box (immobiliser code ECU) or ECM, refer to the Service Bulletin.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the ID code box (immobiliser code ECU) or ECM, refer to the Service Bulletin.
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
- HINT:
- If DTCs other than DTC B279A are output, troubleshoot those DTCs first.
Result Result
Proceed to
No DTC is not output
A
DTC B279A and other DTCs are output
B
DTC B279A is output
C
|
|
||||
|
|
||||
| A | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM) |
Disconnect the G37 ID code box (immobiliser code ECU) connector.
Disconnect the G56*1 or G58*2 G60*3 ECM connector.
- *1: for 1GR-FE
- *2: for 1KD-FTV
- *3: for 2TR-FE
- *1: for 1GR-FE
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for 1GR-FE Tester Connection
Condition
Specified Condition
G37-6 (EFIO) - G56-14 (IMI)
Always
Below 1 Ω
G37-6 (EFIO) or G56-14 (IMI) - Body ground
Always
10 kΩ or higher
for 1KD-FTV Tester Connection
Condition
Specified Condition
G37-6 (EFIO) - G58-28 (IMI)
Always
Below 1 Ω
G37-6 (EFIO) or G58-28 (IMI) - Body ground
Always
10 kΩ or higher
for 2TR-FE Tester Connection
Condition
Specified Condition
G37-6 (EFIO) - G60-31 (IMI)
Always
Below 1 Ω
G37-6 (EFIO) or G60-31 (IMI) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK ID CODE BOX (IMMOBILISER CODE ECU) (OUTPUT) |
Using an oscilloscope, check the waveform.


Text in Illustration *A
for 1GR-FE
*B
for 1KD-FTV
*C
for 2TR-FE
*a
Component with harness connected
(ECM)
Measurement Condition Item
Content
Tester Connection
G56-14 (IMI) - Body ground*1
G58-28 (IMI) - Body ground*2
G60-31 (IMI) - Body ground*3
Tool Setting
10 V/DIV., 100 ms./DIV.
Condition
Engine switch on (IG)
- *1: for 1GR-FE
- *2: for 1KD-FTV
- *3: for 2TR-FE
- OK:
- Waveform is output normally (refer to illustration).
Result Result
Proceed to
NG
A
OK (for 1GR-FE)
B
OK (for 1KD-FTV)
C
OK (for 2TR-FE)
D
- *1: for 1GR-FE
|
|
||||
|
|
||||
|
|
||||
| A | |
| 5. CHECK HARNESS AND CONNECTOR (ID CODE BOX - BATTERY AND BODY GROUND) |
Disconnect the G37 ID code box (immobiliser code ECU) connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
G37-1 (+B) - Body ground
Always
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G37-8 (GND) - Body ground
Always
Below 1 Ω
| *a |
Front view of wire harness connector (to ID Code Box [Immobiliser Code ECU]) |
|
|
||||
| OK | |
| 6. REPLACE ECM |
Temporarily replace the ECM with a new one.
- for 1GR-FE (Click here)
- for 1KD-FTV (Click here)
- for 2TR-FE (Click here)
- for 1GR-FE (Click here)
| NEXT | |
| 7. REGISTER ECU COMMUNICATION ID |
Register the ECU communication ID (Refer to the Service Bulletin).
| NEXT | |
| 8. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 9. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B279A is not output.
|
|
||||
| OK | ||
| ||
