2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B279A Theft Deterrent System Communication Line High Fixation

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

If the communication line (EFIO-IMI) to the ID code box is stuck on HI output, the ECM stores this DTC.
DTC Code
DTC Detection Condition
Trouble Area
B279A
The communication line (EFIO-IMI) between the ECM and the ID code box (immobiliser code ECU) is stuck on HI output.
  1. Harness or connector
  2. ID code box (immobiliser code ECU)
  3. ECM

WIRING DIAGRAM

B355318E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the ID code box (immobiliser code ECU) or ECM, refer to the Service Bulletin.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    If DTCs other than DTC B279A are output, troubleshoot those DTCs first.

    Result 
    Result
    Proceed to
    No DTC is not output
    A
    DTC B279A and other DTCs are output
    B
    DTC B279A is output
    C



B
Go to DIAGNOSTIC TROUBLE CODE CHART (Click here)

C
Go to step 3
A

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM)
  1. Disconnect the G37 ID code box (immobiliser code ECU) connector.

  1. Disconnect the G56*1 or G58*2 G60*3 ECM connector.

    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV
    3. *3: for 2TR-FE

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    G37-6 (EFIO) - G56-14 (IMI)
    Always
    Below 1 Ω
    G37-6 (EFIO) or G56-14 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    G37-6 (EFIO) - G58-28 (IMI)
    Always
    Below 1 Ω
    G37-6 (EFIO) or G58-28 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FE 
    Tester Connection
    Condition
    Specified Condition
    G37-6 (EFIO) - G60-31 (IMI)
    Always
    Below 1 Ω
    G37-6 (EFIO) or G60-31 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK ID CODE BOX (IMMOBILISER CODE ECU) (OUTPUT)

  1. Using an oscilloscope, check the waveform.B242189E08

    Text in Illustration 
    *A
    for 1GR-FE
    *B
    for 1KD-FTV
    *C
    for 2TR-FE
    *a
    Component with harness connected
    (ECM)
    Measurement Condition 
    Item
    Content
    Tester Connection
    G56-14 (IMI) - Body ground*1
    G58-28 (IMI) - Body ground*2
    G60-31 (IMI) - Body ground*3
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Engine switch on (IG)
    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV
    3. *3: for 2TR-FE

    OK:
    Waveform is output normally (refer to illustration).

    Result 
    Result
    Proceed to
    NG
    A
    OK (for 1GR-FE)
    B
    OK (for 1KD-FTV)
    C
    OK (for 2TR-FE)
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)
A


5. CHECK HARNESS AND CONNECTOR (ID CODE BOX - BATTERY AND BODY GROUND)

  1. E180667E04
    Disconnect the G37 ID code box (immobiliser code ECU) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G37-1 (+B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G37-8 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to ID Code Box [Immobiliser Code ECU])


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE ECM
  1. Temporarily replace the ECM with a new one.

    1. for 1GR-FE (Click here)
    2. for 1KD-FTV (Click here)
    3. for 2TR-FE (Click here)


NEXT


7. REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID (Refer to the Service Bulletin).


NEXT


8. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


9. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B279A is not output.



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
OK

END (ECM IS DEFECTIVE)


← B2799 Engine Immobiliser System Malfunction (from Aug 2014)B279A Theft Deterrent System Communication Line High Fixation (from Aug 2014) →