2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

TERMINALS OF ECU

System information · Vehicles built from Aug 2013


CHECK TRANSPONDER KEY AMPLIFIER
B167608E08
  1. Disconnect the G75 amplifier connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G75-7 (AGND) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the G75 amplifier connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G75-1 (VC5) - G75-7 (AGND)
    R - L
    Power supply
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    4.6 to 5.4 V
    G75-4 (CODE) - G75-7 (AGND)
    LG - L
    Demodulated signal of key code data
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (see waveform 1)
    G75-5 (TXCT) - G75-7 (AGND)
    P - L
    Key code output signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (see waveform 2)
    If the result is not as specified, the amplifier may have a malfunction.

  5. B069240E27
    Inspect using an oscilloscope.

    1. Waveform 1 (Reference)

      Measurement Condition 
      Item
      Content
      Tester Connection
      G75-4 (CODE) - G75-7 (AGND)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder

    2. B069239E24
      Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G75-5 (TXCT) - G75-7 (AGND)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder


CHECK TRANSPONDER KEY ECU ASSEMBLY (for 5L-E)
B121962E20
  1. Disconnect the G138 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G138-16 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    G138-1 (+B) - G138-16 (GND)
    P - W-B
    Battery
    Always
    11 to 14 V
    G138-2 (IG) - G138-16 (GND)
    W - W-B
    Ignition switch
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    G138-3 (KSW) - G138-16 (GND)
    G - W-B
    Unlock warning switch
    No key in ignition key cylinder
    10 kΩ or higher
    Key inserted in ignition key cylinder
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the G138 ECU connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G138-14 (VC5) - G138-16 (GND)
    R - W-B
    Power source
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    4.6 to 5.4 V
    G138-7 (CTY) - G138-16 (GND)
    R - W-B*1
    B - W-B*2
    Front door courtesy light switch (for Driver Side)
    Driver door closed
    10 kΩ or higher
    Driver door open
    Below 1 Ω
    G138-4 (TXCT) - G138-16 (GND)
    P - W-B
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (see waveform 1)
    G138-15 (CODE) - G138-16 (GND)
    LG - W-B
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (see waveform 2)
    G138-13 (EFIO) - G138-16 (GND)
    W - W-B
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (see waveform 3)
    G138-12 (EFII) - G138-16 (GND)
    SB - W-B
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected
    Pulse generation (see waveform 4)
    G138-8 (IND) - G138-16 (GND)
    G - W-B
    Security indicator light signal
    Immobiliser set
    Alternating between 11 to 14 V and below 1 V
    Immobiliser unset
    Below 1 V
    G138-9 (D) - G138-16 (GND)
    W - W-B
    Diagnosis tester communication
    Always
    Pulse generation
    G138-5 (AGND) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    1. *1: for LHD
    2. *2: for RHD
    If the result is not as specified, the ECU may have a malfunction.

  5. B069239E25
    Inspect using an oscilloscope.

    1. Waveform 1 (Reference)

      Measurement Condition 
      Item
      Content
      Tester Connection
      G138-4 (TXCT) - G138-16 (GND)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder

    2. B069240E28
      Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G138-15 (CODE) - G138-16 (GND)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder

    3. B237527E01
      Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G138-13 (EFIO) - G138-16 (GND)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Ignition switch ON

    4. B229710E01
      Waveform 4 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G138-12 (EFII) - G138-16 (GND)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected


CHECK TRANSPONDER KEY ECU ASSEMBLY (except 5L-E)
B121962E19
  1. Disconnect the G74 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G74-16 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    G74-1 (+B) - G74-16 (GND)
    P - W-B
    Battery
    Always
    11 to 14 V
    G74-2 (IG) - G74-16 (GND)
    W - W-B
    Ignition switch
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    G74-3 (KSW) - G74-16 (GND)
    G - W-B
    Unlock warning switch
    No key in ignition key cylinder
    10 kΩ or higher
    Key inserted in ignition key cylinder
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the G74 ECU connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G74-14 (VC5) - G74-16 (GND)
    R - W-B
    Power source
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    4.6 to 5.4 V
    G74-7 (CTY) - G74-16 (GND)
    R - W-B*1
    B - W-B*2
    Front door courtesy light switch (for Driver Side)
    Driver door closed
    10 kΩ or higher
    Driver door open
    Below 1 Ω
    G74-4 (TXCT) - G74-16 (GND)
    P - W-B
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (see waveform 1)
    G74-15 (CODE) - G74-16 (GND)
    LG - W-B
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (see waveform 2)
    G74-13 (EFIO) - G74-16 (GND)
    W - W-B
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (see waveform 3)
    G74-12 (EFII) - G74-16 (GND)
    SB - W-B
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected
    Pulse generation (see waveform 4)
    G74-8 (IND) - G74-16 (GND)
    G - W-B
    Security indicator light signal
    Immobiliser set
    Alternating between 11 to 14 V and below 1 V
    Immobiliser unset
    Below 1 V
    G74-9 (D) - G74-16 (GND)
    W - W-B
    Diagnosis tester communication
    Always
    Pulse generation
    G74-5 (AGND) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    1. *1: for LHD
    2. *2: for RHD
    If the result is not as specified, the ECU may have a malfunction.

  5. B069239E25
    Inspect using an oscilloscope.

    1. Waveform 1 (Reference)

      Measurement Condition 
      Item
      Content
      Tester Connection
      G74-4 (TXCT) - G74-16 (GND)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder

    2. B069240E28
      Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G74-15 (CODE) - G74-16 (GND)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder

    3. B237527E01
      Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G74-13 (EFIO) - G74-16 (GND)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Ignition switch ON

    4. B229710E01
      Waveform 4 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G74-12 (EFII) - G74-16 (GND)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected


CHECK ECM (for 2TR-FE)
E195784E08
  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G60-32 (IMO) - Body ground
    SB - Body ground
    Transponder key ECU output signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected
    Pulse generation
    (see waveform 1)
    G60-31 (IMI) - Body ground
    W - Body ground
    Transponder key ECU input signal
    Ignition switch off → ON
    Below 1 V → Pulse generation
    (see waveform 2)
    If the result is not as specified, the ECM may have a malfunction.

  2. Inspect using an oscilloscope.

    1. B229710E01
      Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G60-32 (IMO) - Body ground
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected

    2. B237527E01
      Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G60-31 (IMI) - Body ground
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Ignition switch ON


CHECK ECM (for 1GR-FE)
E195784E06
  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G56-20 (IMO) - Body ground
    SB - Body ground
    Transponder key ECU output signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected
    Pulse generation
    (see waveform 1)
    G56-14 (IMI) - Body ground
    W - Body ground
    Transponder key ECU input signal
    Ignition switch off → ON
    Below 1 V → Pulse generation
    (see waveform 2)
    If the result is not as specified, the ECM may have a malfunction.

  2. Inspect using an oscilloscope.

    1. B229710E01
      Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G56-20 (IMO) - Body ground
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected

    2. B237527E01
      Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G56-14 (IMI) - Body ground
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Ignition switch ON


CHECK ECM (for 1KD-FTV)
E195784E07
  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G58-29 (IMO) - Body ground
    SB - Body ground
    Transponder key ECU output signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected
    Pulse generation
    (see waveform 1)
    G58-28 (IMI) - Body ground
    W - Body ground
    Transponder key ECU input signal
    Ignition switch off → ON
    Below 1 V → Pulse generation
    (see waveform 2)
    If the result is not as specified, the ECM may have a malfunction.

  2. Inspect using an oscilloscope.

    1. B229710E01
      Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G58-29 (IMO) - Body ground
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected

    2. B237527E01
      Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G58-28 (IMI) - Body ground
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Ignition switch ON


CHECK ECM (for 5L-E)
A139495E02
  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G61-6 (IMO) - Body ground
    SB - Body ground
    Transponder key ECU output signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected
    Pulse generation
    (see waveform 1)
    G61-17 (IMI) - Body ground
    W - Body ground
    Transponder key ECU input signal
    Ignition switch off → ON
    Below 1 V → Pulse generation
    (see waveform 2)
    If the result is not as specified, the ECM may have a malfunction.

  2. Inspect using an oscilloscope.

    1. B229710E01
      Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G61-6 (IMO) - Body ground
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected

    2. B237527E01
      Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G61-17 (IMI) - Body ground
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Ignition switch ON

← PROBLEM SYMPTOMS TABLE (from Aug 2014)DTC CHECK / CLEAR (from Aug 2013) →