2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1612/83 Lost Communication with Front Airbag Sensor RH

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The front airbag sensor RH circuit consists of the center airbag sensor and front airbag sensor RH.
The front airbag sensor RH detects impacts to the vehicle and sends signals to the center airbag sensor to determine if the airbag should be deployed.
DTC B1612/83 or B1613/83 is stored when a malfunction is detected in the front airbag sensor RH circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1612/83
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.
  2. A front airbag sensor RH malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor RH
  4. Center airbag sensor assembly
B1613/83
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.
  2. A front airbag sensor RH malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor RH
  4. Center airbag sensor assembly

WIRING DIAGRAM

C213916E03

INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).


1. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and front airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and front airbag sensor RH.

  1. C213959E01
    Check that the connectors (on the center airbag sensor side and front airbag sensor RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Center Airbag Sensor



NG
REPLACE HARNESS AND CONNECTOR
OK


3. CHECK FRONT AIRBAG SENSOR RH CIRCUIT

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.C214250E02

    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Center Airbag Sensor
    *3
    Connector E
    *4
    Connector B
    *5
    Service Wire
    -
    -
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor RH)
    *b
    Rear view of wire harness connector
    (to Center Airbag Sensor)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A20-2 (+SR) - Body ground
    Ignition switch ON
    Below 1 V
    A20-1 (-SR) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A20-2 (+SR) - A20-1 (-SR)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A20-2 (+SR) - A20-1 (-SR)
    Always
    1 MΩ or higher
    A20-2 (+SR) - Body ground
    Always
    1 MΩ or higher
    A20-1 (-SR) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 5
OK


4. CHECK FRONT AIRBAG SENSOR RH

  1. C171014E01
    Connect the connectors to the center airbag sensor.

  1. Interchange the front airbag sensor LH with RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1612, B1613, B1617 and B1618 are not output
    A
    DTC B1617 or B1618 is output
    B
    DTC B1612 or B1613 is output
    C

    HINT:
    Codes other than DTC B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Center Airbag Sensor



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE FRONT AIRBAG SENSOR RH (Click here)
C

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

5. CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - ENGINE ROOM MAIN WIRE)

  1. Disconnect the instrument panel wire connector from the engine room main wire.C214251E02

    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Center Airbag Sensor
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *5
    Connector C
    *6
    Connector B
    *7
    Service Wire
    -
    -
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)
    *b
    Rear view of wire harness connector
    (to Center Airbag Sensor)

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    GA5-1 (+SR) - Body ground
    Ignition switch ON
    Below 1 V
    GA5-2 (-SR) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    GA5-1 (+SR) - GA5-2 (-SR)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    GA5-1 (+SR) - GA5-2 (-SR)
    Always
    1 MΩ or higher
    GA5-1 (+SR) - Body ground
    Always
    1 MΩ or higher
    GA5-2 (-SR) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE


← B1610/13 Front Airbag Sensor RH Malfunction (from Aug 2014)B1612/83 Lost Communication with Front Airbag Sensor RH (+ B1613/83) (from Aug 2014) →