B1612/83 Lost Communication with Front Airbag Sensor RH
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- B1613/83 Front Airbag Sensor RH Initialization Incomplete
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The front airbag sensor RH circuit consists of the center airbag sensor and front airbag sensor RH.The front airbag sensor RH detects impacts to the vehicle and sends signals to the center airbag sensor to determine if the airbag should be deployed.
DTC B1612/83 or B1613/83 is stored when a malfunction is detected in the front airbag sensor RH circuit.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1612/83 |
One of the following conditions is met:
|
|
| B1613/83 |
One of the following conditions is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
- When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| 1. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and front airbag sensor RH.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 2. CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and front airbag sensor RH.
Check that the connectors (on the center airbag sensor side and front airbag sensor RH side) are not damaged.

- OK:
- The connectors are not deformed or damaged.
Text in Illustration *1
Front Airbag Sensor RH
*2
Center Airbag Sensor
|
|
||||
| OK | |
| 3. CHECK FRONT AIRBAG SENSOR RH CIRCUIT |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


Text in Illustration *1
Front Airbag Sensor RH
*2
Center Airbag Sensor
*3
Connector E
*4
Connector B
*5
Service Wire
-
-
*a
Front view of wire harness connector
(to Front Airbag Sensor RH)
*b
Rear view of wire harness connector
(to Center Airbag Sensor)
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A20-2 (+SR) - Body ground
Ignition switch ON
Below 1 V
A20-1 (-SR) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A20-2 (+SR) - A20-1 (-SR)
Always
Below 1 Ω
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A20-2 (+SR) - A20-1 (-SR)
Always
1 MΩ or higher
A20-2 (+SR) - Body ground
Always
1 MΩ or higher
A20-1 (-SR) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK FRONT AIRBAG SENSOR RH |
Connect the connectors to the center airbag sensor.

Interchange the front airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1612, B1613, B1617 and B1618 are not output
A
DTC B1617 or B1618 is output
B
DTC B1612 or B1613 is output
C
- HINT:
- Codes other than DTC B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.
Text in Illustration *1
Front Airbag Sensor LH
*2
Center Airbag Sensor
|
|
||||
|
|
||||
| C | ||
| ||
| 5. CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - ENGINE ROOM MAIN WIRE) |
Disconnect the instrument panel wire connector from the engine room main wire.


Text in Illustration *1
Front Airbag Sensor RH
*2
Center Airbag Sensor
*3
Engine Room Main Wire
*4
Instrument Panel Wire
*5
Connector C
*6
Connector B
*7
Service Wire
-
-
*a
Front view of wire harness connector
(to Engine Room Main Wire)
*b
Rear view of wire harness connector
(to Center Airbag Sensor)
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
GA5-1 (+SR) - Body ground
Ignition switch ON
Below 1 V
GA5-2 (-SR) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
GA5-1 (+SR) - GA5-2 (-SR)
Always
Below 1 Ω
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
GA5-1 (+SR) - GA5-2 (-SR)
Always
1 MΩ or higher
GA5-1 (+SR) - Body ground
Always
1 MΩ or higher
GA5-2 (-SR) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | ||
| ||
