2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

DISASSEMBLY

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ Bracket)

  1. B357945
    Remove the 2 screws and front bumper extension mounting bracket.


2. REMOVE FRONT SPOILER LH (w/ Front Spoiler)

  1. B353281E01
    Turn the 2 front spoiler No. 1 retainers 90° and remove the 2 front spoiler No. 1 retainers and front spoiler LH.


3. REMOVE FRONT SPOILER RH (w/ Front Spoiler)

HINT:
Use the same procedure described for the LH side.


4. REMOVE FRONT BUMPER REINFORCEMENT STOPPER RH (w/ Fog Light)

  1. B353280
    Detach the 2 claws and front bumper reinforcement stopper RH.


5. REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light)

E282559
  1. Disconnect the connector.

  1. Remove the 2 screws.

  1. Detach the 2 guides and remove the fog light assembly LH.


6. REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure described for the LH side.


7. REMOVE FOG LIGHT COVER LH (w/ Fog Light)

  1. B353282
    Remove the screw.

  1. Detach the 3 clips and remove the fog light cover LH.


8. REMOVE FOG LIGHT COVER RH (w/ Fog Light)

HINT:
Use the same procedure described for the LH side.


9. REMOVE FRONT BUMPER HOLE COVER LH (w/o Fog Light)

  1. B357943
    Remove the screw.

  1. Detach the 3 clips and remove the front bumper hole cover LH.


10. REMOVE FRONT BUMPER HOLE COVER RH (w/o Fog Light)

HINT:
Use the same procedure described for the LH side.


11. REMOVE TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

  1. E197819E01
    Using a screwdriver, detach the 2 claws and separate the washer nozzle sub-assembly as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the windshield.

  1. E197820
    Disconnect the washer nozzle sub-assembly from the washer hose.

    NOTICE:
    Washer nozzles cannot be reused.


12. REMOVE TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.


13. REMOVE NO. 1 HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)

  1. E283257
    Disconnect the No. 1 headlight cleaner hose from the headlight washer actuator sub-assembly.

  1. Detach the 5 clamps and remove the No. 1 headlight cleaner hose from the front bumper cover.


14. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

  1. E283258E01
    Remove the headlight cleaner clamp as shown in the illustration.
    Text in Illustration 
    *1
    Headlight Cleaner Clamp

  1. E283259E01
    Pull down the headlight cleaner clamp B and remove it.
    Text in Illustration 
    *1
    Headlight Cleaner Clamp B

  1. Push the tab shown by arrow 1, detach the 2 claws and remove the headlight washer actuator sub-assembly LH as shown in the illustration.

    E283260E01


15. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.


16. REMOVE NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

E197640

HINT:
Use the same procedure to remove the No. 1 ultrasonic sensor on the other side.

  1. Disconnect the connector.

  1. Detach the 2 claws and remove the No. 1 ultrasonic sensor.


17. REMOVE NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

E200377

HINT:
Use the same procedure to remove the No. 1 ultrasonic sensor retainer on the other side.

  1. Detach the 2 claws and remove the No. 1 ultrasonic sensor retainer.


18. REMOVE NO. 2 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)

  1. B353279
    Detach the 7 clamps and remove the No. 2 engine room wire.


19. REMOVE LOWER NO. 1 RADIATOR GRILLE

  1. B353283
    Detach the 18 claws and remove the lower No. 1 radiator grille.

← REMOVAL (from Aug 2014)DISASSEMBLY (from Aug 2014) →