2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

REASSEMBLY

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL LOWER NO. 1 RADIATOR GRILLE
  1. Attach the 18 claws to install the lower No. 1 radiator grille.


2. INSTALL NO. 2 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)
  1. Attach the 7 clamps to install the No. 2 engine room wire.


3. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

E200376E01

HINT:
Use the same procedure to install the No. 1 ultrasonic sensor retainer on the other side.

  1. Align the keyhole and protrusion as shown in the illustration.

  1. Install the No. 1 ultrasonic sensor retainer to the front bumper cover.

    NOTICE:
    Do not damage the bumper cover with the protrusion when installing the retainer.

    Text in Illustration 
    *1
    Keyhole


4. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

HINT:
Use the same procedure to install the No. 1 ultrasonic sensor on the other side.

  1. Attach the 2 claws to install the No. 1 ultrasonic sensor.

  1. Connect the connector.


5. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

  1. E283264
    Attach the 2 claws to install the headlight washer actuator sub-assembly LH as shown in the illustration.

  1. E283265E01
    Push up the headlight cleaner clamp B to install it.
    Text in Illustration 
    *1
    Headlight Cleaner Clamp B

  1. E283266E01
    Install the headlight washer actuator sub-assembly LH with the headlight cleaner clamp as shown in the illustration.
    Text in Illustration 
    *1
    Headlight Cleaner Clamp
    *2
    Headlight Washer Actuator Sub-assembly LH
    *3
    Headlight Cleaner Clamp B
    V100155
    Push Here


6. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.


7. INSTALL NO. 1 HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)
  1. Attach the 5 clamps to install the No. 1 headlight cleaner hose to the front bumper cover.

  1. Connect the No. 1 headlight cleaner hose to the headlight washer actuator sub-assembly.


8. INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)
  1. Connect a new washer nozzle sub-assembly to the washer hose.

  1. Attach the 2 claws to install the washer nozzle sub-assembly.


9. INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.


10. INSTALL FOG LIGHT COVER LH (w/ Fog Light)
  1. Attach the 3 clips to install the fog light cover LH.

  1. Install the screw.


11. INSTALL FOG LIGHT COVER RH (w/ Fog Light)

HINT:
Use the same procedure described for the LH side.


12. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)
  1. Attach the 2 guides to install the fog light assembly LH.

  1. Install the 2 screws.

  1. Connect the connector.


13. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure described for the LH side.


14. INSTALL FRONT BUMPER REINFORCEMENT STOPPER RH (w/ Fog Light)
  1. Attach the 2 claws to install the front bumper reinforcement stopper RH.


15. INSTALL FRONT BUMPER HOLE COVER LH (w/o Fog Light)
  1. Attach the 3 clips to install the front bumper hole cover LH.

  1. Install the screw.


16. INSTALL FRONT BUMPER HOLE COVER RH (w/o Fog Light)

HINT:
Use the same procedure described for the LH side.


17. INSTALL FRONT SPOILER LH (w/ Front Spoiler)
  1. Install the front spoiler LH with the 2 front spoiler No. 1 retainers.


18. INSTALL FRONT SPOILER RH (w/ Front Spoiler)

HINT:
Use the same procedure described for the LH side.


19. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ Bracket)
  1. Install the front bumper extension mounting bracket with the 2 screws.

← REASSEMBLY (Aug 2013 – Jul 2014)INSTALLATION (Aug 2013 – Jul 2014) →