2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. When removing the window frame moulding, heat the vehicle body and window frame moulding using a heat light.

    Standard:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)
    Window Frame Moulding
    20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or window frame moulding excessively.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

  1. B240614
    Detach the 2 clips and remove the front door lower frame bracket garnish LH.


4. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

  1. B238520
    Using a moulding remover, detach the 3 claws and remove the inside handle bezel as shown in the illustration.


5. REMOVE ASSIST GRIP COVER LH

  1. B238521
    Using moulding remover A, detach the 8 claws and remove the assist grip cover.


6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B238522
    Remove the 3 screws.

  1. Remove the 12 clips.

  1. B238523E01
    Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.
    Text in Illustration 
    *1
    Reference Boss

  1. Raise the front door trim board sub-assembly to detach the 4 claws and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip LH.

  1. B238524
    Disconnect the 2 connectors.

  1. w/ Seat Position Memory System:

    1. B240206
      Disconnect the connectors.

  1. B238525
    Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.


7. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

  1. B238526
    Using a screwdriver, detach the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.


8. REMOVE FRONT DOOR SERVICE HOLE COVER LH

  1. B238530
    Remove the bolt.

  1. Detach the 2 clamps, move the wire harness out of the way and remove the service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.


9. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

B231561
  1. Disconnect the connector.

  1. Remove the 3 nuts.

  1. Detach the claw and remove the outer rear view mirror.


10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. B238531
    Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.

  1. B238532E01
    Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.


11. REMOVE FRONT DOOR GLASS RUN LH

  1. B238535
    Remove the front door glass run.


12. REMOVE FRONT DOOR BELT MOULDING LH

B236327E01
  1. Put protective tape around the belt moulding.

  1. Detach the 6 claws and remove the front door belt moulding.

    Text in Illustration 
    *1
    Protective Tape


13. REMOVE FRONT DOOR WEATHERSTRIP LH

B236328
  1. Detach the 3 clips and remove the upper part of the front door weatherstrip so that the moulding can be removed.


14. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

  1. B243888
    Remove the door window frame moulding clip.

  1. B243889E01
    Put protective tape around the front door rear window frame moulding.

  1. Using a moulding remover, detach the clip and remove the double-sided tape to remove the front door rear window frame moulding.

    Text in Illustration 
    *1
    Protective Tape
    *2
    Double-sided Tape
    *3
    Moulding Remover

← REMOVAL (Aug 2013 – Jul 2014)INSTALLATION (Aug 2013 – Jul 2014) →