When removing the window frame moulding, black out tape and outside stripe, heat the vehicle body, window frame moulding, black out tape and outside stripe using a heat light.
Standard:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Window Frame Moulding
20 to 30°C (68 to 86°F)
Black Out Tape
20 to 30°C (68 to 86°F)
Outside Stripe
20 to 30°C (68 to 86°F)
NOTICE:
Do not heat the vehicle body, window frame moulding, black out tape and outside stripe excessively.
1.
PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
3.
REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH
Detach the 2 clips and remove the front door lower frame bracket garnish LH.
4.
REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH
Using a moulding remover, detach the 3 claws and remove the inside handle bezel as shown in the illustration.
5.
REMOVE ASSIST GRIP COVER LH
Using moulding remover A, detach the 8 claws and remove the assist grip cover.
6.
REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
Remove the 3 screws.
Remove the 12 clips.
Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.
Text in Illustration
*1
Reference Boss
Raise the front door trim board sub-assembly to detach the 4 claws and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip LH.
Disconnect the 2 connectors.
w/ Seat Position Memory System:
Disconnect the connectors.
Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.
7.
REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH
Using a screwdriver, detach the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.
8.
REMOVE FRONT DOOR SERVICE HOLE COVER LH
Remove the bolt.
Detach the 2 clamps, move the wire harness out of the way and remove the service hole cover.
HINT:
Remove any remaining butyl tape from the door.
9.
REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH
Disconnect the connector.
Remove the 3 nuts.
Detach the claw and remove the outer rear view mirror.
10.
REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
Connect the cable to the negative (-) battery terminal.
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
Remove the 2 bolts.
NOTICE:
After the bolts are removed, do not allow the door glass to fall.
Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.
NOTICE:
Do not damage the door glass.
11.
REMOVE FRONT DOOR GLASS RUN LH
Remove the front door glass run.
12.
REMOVE FRONT DOOR BELT MOULDING LH
Put protective tape around the belt moulding.
Detach the 6 claws and remove the front door belt moulding.
Text in Illustration
*1
Protective Tape
13.
REMOVE FRONT DOOR WEATHERSTRIP LH
Detach the 3 clips and remove the upper part of the front door weatherstrip so that the moulding can be removed.
14.
REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH
Remove the door window frame moulding clip.
Put protective tape around the front door rear window frame moulding.
Using a moulding remover, detach the clip and remove the double-sided tape to remove the front door rear window frame moulding.
Text in Illustration
*1
Protective Tape
*2
Double-sided Tape
*3
Moulding Remover
15.
REMOVE NO. 1 BLACK OUT TAPE LH
Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.
16.
REMOVE FRONT DOOR OUTSIDE STRIPE LH
Pull back an edge of the front door outside stripe and pull it parallel to the vehicle body to remove it.
17.
REMOVE LOWER FRONT DOOR OUTSIDE STRIPE LH
Pull back an edge of the lower front door outside stripe and pull it parallel to the vehicle body to remove it.