2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. REMOVE SIDE STEP BRACKET LH

B236305
  1. Remove the 2 bolts and side step bracket.


2. REMOVE NO. 2 SIDE STEP BRACKET LH

B236306
  1. Remove the 2 bolts and No. 2 side step bracket.


3. REMOVE NO. 3 SIDE STEP BRACKET LH

B236307
  1. Remove the 2 bolts and No. 3 side step bracket.


4. REMOVE NO. 2 ROCKER PANEL MOULDING PROTECTOR

B236308
  1. Remove the 2 bolts and No. 2 rocker panel moulding protector.


5. REMOVE STEP PLATE LH (for 5 Door)
  1. Remove the clip and 3 bolts.

  1. Detach the 17 claws and remove the step plate.

    B236309


6. REMOVE STEP PLATE LH (for 3 Door)
  1. Remove the clip and 3 bolts.

  1. Detach the 14 claws and remove the step plate.

    B236310


7. REMOVE STEP PLATE COVER LH

  1. Remove the step plate cover.

    B236311E01

    Text in Illustration 
    *A
    for 5 Door
    *B
    for 3 Door


8. REMOVE NO. 2 SIDE STEP PLATE COVER

  1. Remove the No. 2 step plate cover.

    B236312E01

    Text in Illustration 
    *A
    for 5 Door
    *B
    for 3 Door


9. REMOVE SIDE STEP BRACKET SUB-ASSEMBLY LH
  1. Put a 4 mm (0.157 in.) drill bit into a drill.

  1. B236315E01
    Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

    HINT:
    Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

  1. Lightly press the drill against the 3 rivets, drill off the flanges of the 3 rivets and remove the side step bracket.

    CAUTION:
    Be careful of the drilled rivet as it may become hot.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.


10. REMOVE STEP PANEL WIRE LH (w/ Illumination)

  1. E198149E01
    for 5 Door:

    1. Detach the 9 clamps and remove the wire.

  1. for 3 Door:

    1. Detach the 5 clamps and remove the wire.

      Text in Illustration 
      *A
      for 5 Door:
      *B
      for 3 Door:


11. REMOVE STEP LIGHT ASSEMBLY (w/ Illumination)

  1. E198150
    Turn the socket in the direction indicated by the arrow and remove it.

  1. Remove the bulb.


12. REMOVE STEP LIGHT BRACKET (w/ Illumination)

B236313E01
  1. Put a 4 mm (0.157 in.) drill bit into a drill.

  1. Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

    HINT:
    Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

  1. Lightly press the drill against the 3 rivets, drill off the flanges of the 3 rivets and remove the step light bracket.

    CAUTION:
    Be careful of the drilled rivet as it may become hot.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.


13. REMOVE STEP LIGHT ASSEMBLY (w/ Illumination)

  1. E198147
    for 5 Door:

    1. Remove the 4 bolts and 2 lights.

  1. for 3 Door:

    1. Remove the 2 bolts and light.

← REMOVAL (from Aug 2013)REASSEMBLY (from Aug 2013) →