2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REPLACEMENT

Removal / installation · Vehicles built from Aug 2013

NOTICE:
Take extra care when handling these precision electronic components.


1. REMOVE TRANSMITTER BATTERY (for Type A)

  1. B208996
    Push the release hook knob and extract the emergency key.

  1. B208997E01
    Insert a precision screwdriver into the gap, and turn the screwdriver to detach the transmitter housing cover.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

  1. B107853
    Remove the transmitter battery (lithium battery: CR1632).

    NOTICE:
    1. Do not push the terminals with your finger.
    2. Do not forcibly pry up the transmitter battery. The terminals may be damaged.
    3. Do not touch the transmitter battery with wet hands. Water may cause rust.
    4. Do not touch or move any components inside the transmitter. It may interfere with proper operation.
    5. When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical transmitter from being damaged.


2. INSTALL TRANSMITTER BATTERY (for Type A)

  1. B107853
    Install a new transmitter battery (lithium battery: CR1632) with the positive (+) side facing upward as shown in the illustration.

    NOTICE:
    1. Be careful not to bend the transmitter battery electrode during insertion.
    2. Keep the transmitter cover interior free of dust and oil.
    3. When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical transmitter housing case from being damaged.

  1. Install the transmitter housing cover by pressing down on it.

  1. Insert the emergency key into the transmitter.

  1. Press one of the transmitter switches and check that the LED illuminates.


3. REMOVE TRANSMITTER BATTERY (for Type B)

  1. B356205
    Push the release hook knob and extract the emergency key.

  1. B356206E01
    Insert a precision screwdriver into the gap, and turn the screwdriver to detach the transmitter housing cover.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

  1. B356452E01
    Insert a precision screwdriver into the gap and gently remove the transmitter battery (lithium battery: CR2032).
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    1. Do not push the terminals with your finger.
    2. Do not forcibly pry up the transmitter battery. The terminals may be damaged.
    3. Do not touch the transmitter battery with wet hands. Water may cause rust.
    4. Do not touch or move any components inside the transmitter. It may interfere with proper operation.
    5. When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical transmitter from being damaged.


4. INSTALL TRANSMITTER BATTERY (for Type B)

  1. B311757
    Install a new transmitter battery (lithium battery: CR2032) with the positive (+) side facing upward as shown in the illustration.

    NOTICE:
    1. Be careful not to bend the transmitter battery electrode during insertion.
    2. Keep the transmitter cover interior free of dust and oil.
    3. When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical transmitter housing case from being damaged.

  1. B356207
    Install the transmitter housing cover by pressing down on it as shown in the illustration.

  1. Insert the emergency key into the transmitter.

  1. Press one of the transmitter switches and check that the LED illuminates.

← Key Reminder Buzzer does not Sound (from Aug 2014)REPLACEMENT (from Aug 2013) →