2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Key Reminder Buzzer does not Sound

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The key reminder warning buzzer sounds when the driver side door is opened while the ignition switch is ACC or off and the key is in the ignition key cylinder. The key reminder warning buzzer is activated when the main body ECU sends an unlock warning switch signal and front door courtesy light switch LH*1 or RH*2 signal to the combination meter.
  1. *1: for LHD
  2. *2: for RHD

WIRING DIAGRAM

E200519E01

INSPECTION PROCEDURE

HINT:
Since the key reminder warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting CAN communication in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


1. READ VALUE USING INTELLIGENT TESTER (FRONT DOOR COURTESY LIGHT SWITCH)
  1. Check the Data List for proper functioning of the front door courtesy light switch (Click here).

    1. for LHD:

      Main Body 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      FL Door Courtesy
      Front door courtesy light switch LH signal / ON or OFF
      ON: Front door LH closed
      OFF: Front door LH open
      -

    2. for RHD:

      Main Body 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      FR Door Courtesy
      Front door courtesy light switch RH signal / ON or OFF
      ON: Front door RH closed
      OFF: Front door RH open
      -

      OK:
      On tester screen, each item changes between ON and OFF according to above chart.



NG
GO TO LIGHTING SYSTEM (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (UNLOCK WARNING SWITCH)
  1. Check the Data List for proper functioning of the unlock warning switch (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Unlock Warning SW
    Unlock warning switch signal / ON or OFF
    ON: Key in ignition key cylinder
    OFF: No key in ignition key cylinder
    -

    OK:
    On tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 3
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

3. INSPECT UNLOCK WARNING SWITCH ASSEMBLY

  1. E198930E02
    Remove the unlock warning switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (UN+) - 2 (UN-)
    Not pushed
    10 kΩ or higher
    Pushed
    Below 1 Ω



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
  1. Disconnect the G3 unlock warning switch connector.

  1. Disconnect the G64 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G3-1 (UN+) - G64-17 (KSW)
    Always
    Below 1 Ω
    G3-2 (UN-) - Body ground
    Always
    Below 1 Ω
    G64-17 (KSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK COMBINATION METER ASSEMBLY (OPERATION)
  1. Temporarily replace the combination meter assembly with a new or normally functioning one (Click here).

  1. Check the key reminder warning system (Click here).

    OK:
    The key reminder warning system functions properly.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (COMBINATION METER IS DEFECTIVE)


← Key Reminder Buzzer does not Sound (Aug 2013 – Jul 2014)REPLACEMENT (from Aug 2013) →