2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. INSTALL REAR DOOR BELT MOULDING LH
  1. Attach the 7 claws to install the rear door belt moulding.


2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the cable to the negative (-) battery terminal and rear power window regulator motor connector.

  1. B241339
    Connect the power window regulator switch assembly and move the arm of the regulator so that the roller on the arm can be seen through the service hole.

  1. Disconnect the power window regulator switch assembly and rear power window regulator motor connector.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. B239637
    Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as indicated by the arrow in the illustration.


3. INSTALL REAR DOOR QUARTER WINDOW GLASS LH

  1. B239633
    Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.


4. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
  1. Insert the rear door window division bar sub-assembly from above.

  1. Install the rear door window division bar sub-assembly to the glass run.

  1. Install the temporary bolt to the rear door window division bar sub-assembly.

  1. Install the rear door window division bar sub-assembly.

  1. Install the 2 bolts and screw.

  1. Tighten the temporary bolt to install the rear door window division bar sub-assembly.


5. INSTALL REAR DOOR GLASS RUN LH
  1. Install the glass run.


6. INSTALL REAR DOOR SERVICE HOLE COVER LH
  1. Apply new butyl tape to the rear door panel.

  1. B239701E01
    Pass the rear door lock remote control cable assembly and rear door inside locking cable assembly through a new rear door service hole cover.

  1. Attach the rear door service hole cover using to the reference points on the rear door panel.

    Text in Illustration 
    *1
    Reference Point

    NOTICE:
    1. There should be no wrinkles or folds after attaching the service hole cover.
    2. After attaching the service hole cover, check the seal quality.

  1. Connect the connector.

  1. Attach the 2 clamps to the rear door wire.


7. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

  1. B239678
    Attach the 3 claws to install the rear door inner glass weatherstrip as shown in the illustration.


8. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B239618
    Attach the guide and 2 claws to install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.

  1. Install the 2 screws.

  1. B239610
    Install the 8 screws to the rear door armrest.


9. INSTALL ASSIST GRIP COVER LH

  1. B241356
    Attach the 8 claws to install the assist grip cover.


10. INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH

  1. B241355
    Attach the 3 claws to install the door inside handle bezel.


11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSTALLATION (Aug 2013 – Jul 2014)COMPONENTS (from Aug 2013) →