2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT BUMPER COVER LOWER
  1. Remove the clip, 5 bolts and front bumper cover lower.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.

  1. A224743
    Unhook the engine under cover from the vehicle body as shown in the illustration.


4. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


A273797E01
Text in Illustration 
*1
Reservoir Cap
*2
Radiator Cap
*3
Radiator Drain Cock Plug
*4
Cylinder Block Drain Cock Plug
  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the coolant from the engine.


6. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


7. DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

8. REMOVE BATTERY HOLD DOWN CLAMP

  1. A223416
    Loosen the 2 nuts and remove the battery hold down clamp.


9. REMOVE BATTERY

10. REMOVE BATTERY TRAY

11. REMOVE V-BANK COVER

  1. A229925E01
    Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Pin
    *2
    Hook


12. REMOVE AIR CLEANER CAP AND HOSE

  1. A224721
    Remove the air cleaner cap and hose.

    1. Disconnect the mass air flow meter connector, vacuum hose and ventilation hose and detach the 4 clamps.

    2. Loosen the clamp.

    3. Unfasten the 4 hook clamps, and then remove the bolt and air cleaner cap and hose.


13. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
  1. Remove the air cleaner filter element.

  1. A224715
    Detach the wire harness clamp.

  1. Remove the 3 bolts and air cleaner case.


14. REMOVE NO. 1 RADIATOR HOSE

A223076

15. REMOVE NO. 2 RADIATOR HOSE

  1. A223077
    Disconnect the radiator hose from the water inlet.

  1. A223078
    Detach the clamp and remove the radiator hose.


16. REMOVE RADIATOR RESERVOIR

  1. A223079
    Disconnect the reservoir hose from the upper side of the radiator tank.

  1. Remove the 3 bolts and radiator reservoir.


17. DISCONNECT OIL COOLER TUBE (w/ Warmer)

  1. A223080
    Detach the claw to open the flexible hose clamp, and then remove the 2 bolts to disconnect the oil cooler tube from the fan shroud.


18. DISCONNECT OIL COOLER TUBE (w/ Air Cooled Transmission Oil Cooler)

  1. A223081
    Detach the claw to open the flexible hose clamp, and then remove the 2 bolts to disconnect the oil cooler tube from the fan shroud.


19. REMOVE FAN SHROUD

  1. A223082
    Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and generator V-belt (Click here).

  1. A223083
    Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.


20. REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)

  1. A221459
    for Bank 1 Side:
    Remove the bolt and disconnect the air tube assembly from the emission control valve set.

  1. A221458
    for Bank 2 Side:
    Remove the 2 bolts and disconnect the air tube assembly from the No. 2 emission control valve set.


21. REMOVE INTAKE AIR SURGE TANK

  1. A221456
    Disconnect the throttle body connector.

  1. Disconnect the No. 4 water by-pass hose.

  1. Disconnect the No. 5 water by-pass hose.

  1. A221457
    Disconnect the No. 1 fuel vapor feed hose.

  1. Disconnect the No. 1 vacuum switching valve connector.

  1. Disconnect the No. 1 ventilation hose.

  1. A221464
    Detach the 2 heater hose clamps.

  1. A221460
    Remove the 2 bolts and throttle body bracket.

  1. A221461
    Using a clip remover, detach the wire harness clamp.

  1. A221462
    Remove the 2 bolts and No. 1 surge tank stay.

  1. A221463
    Remove the 2 bolts and No. 2 surge tank stay.

  1. A221465
    Remove the 2 nuts, 4 bolts and intake air surge tank.

  1. Remove the gasket.


22. REMOVE AIR TUBE (w/ Secondary Air Injection System)

  1. A223569
    Remove the 2 bolts, 2 nuts and air tube.

  1. Remove the 2 gaskets from the air tube.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.


23. REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)

  1. A223563
    Remove the 2 bolts, 2 nuts and No. 2 air tube.

  1. Remove the 2 gaskets from the No. 2 air tube.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.


24. REMOVE EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

  1. A223568
    Disconnect the emission control valve set connector.

  1. Disconnect the No. 1 air hose from the emission control valve set.

  1. A223570
    Remove the 3 nuts and emission control valve set.


25. REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

  1. A223562
    Disconnect the No. 2 emission control valve set connector.

  1. Disconnect the No. 3 air hose.

  1. A223564
    Remove the 3 nuts and No. 2 emission control valve set.


26. REMOVE IGNITION COIL ASSEMBLY

  1. A221430
    Disconnect the 6 ignition coil connectors.

  1. Remove the 6 bolts and 6 ignition coils.


27. DISCONNECT VANE PUMP ASSEMBLY

  1. A223016
    Disconnect the 2 connectors.

  1. Detach the 2 wire harness clamps.

  1. A223015
    Remove the 2 bolts and disconnect the vane pump.


28. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A223415
    for Integrated Type:
    Remove the bolt and No. 2 idler pulley.

  1. for Separate Type:
    Remove the bolt, No. 2 idler pulley cover plate, No. 2 idler pulley and idler pulley cover plate.


29. REMOVE WIRING HARNESS CLAMP BRACKET

  1. A222903
    Detach the clamp.

  1. Remove the bolt and wiring harness clamp bracket.


30. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A221484
    Remove the 3 bolts and heat insulator.


31. REMOVE GENERATOR ASSEMBLY

  1. A222881
    Open the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Disconnect the generator connector from the generator assembly.

  1. A222884
    Remove the 2 bolts and disconnect the wire harness.

  1. A222882
    Disconnect the wire harness clamp.

  1. Remove the bolt and disconnect the generator bracket.

  1. A222883
    Remove the 2 bolts and generator assembly.

  1. A222885
    Remove the bolt and generator bracket.


32. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A222114
    Remove the dipstick.

  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.


33. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY (w/ Oil Cooler)

  1. A223013
    Disconnect the 2 hoses.

  1. Remove the 3 bolts and water by-pass pipe.


34. REMOVE NO. 1 OIL PIPE

  1. A223691
    Remove the 2 oil pipe unions, oil control valve filter LH, 3 gaskets and No. 1 oil pipe.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.


35. REMOVE NO. 2 OIL PIPE

  1. A223692
    Remove the 2 oil pipe unions, oil control valve filter RH, 3 gaskets and No. 2 oil pipe.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.


36. REMOVE REAR CYLINDER HEAD COVER

  1. A224695
    Remove the 3 bolts and cover.


37. DISCONNECT FUEL PIPE SUB-ASSEMBLY
  1. Remove the 2 bolts and disconnect the fuel pipe.


38. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

  1. A223666
    Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A223665
    Remove the 3 gaskets.


39. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A223669
    Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A223668
    Remove the 3 gaskets.


40. REMOVE TIMING CHAIN COVER PLATE

  1. A224737
    Remove the 4 bolts, timing chain cover plate and gasket.


41. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A072945E01
    Turn the crankshaft pulley and align the notch with the "0" timing mark of the timing chain cover.

  1. A224754E01
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
    Text in Illustration 
    *A
    for Bank 2
    *B
    for Bank 1
    *1
    Paint Mark

    HINT:
    If the marks are not aligned, turn the crankshaft again to align the marks.

  1. Place paint marks on the timing marks and sprockets of each camshaft timing gear and on the links of the No. 1 chain.

    HINT:
    Be sure to place the paint marks on 2 links of the chain and on the sprockets of the camshaft timing gears at the locations of the timing marks of the camshaft timing gears.


42. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A226510E01
    Turn the crankshaft approximately 30° counterclockwise so that there is some slack in the chain.

    HINT:
    This prevents the valves and pistons from interfering with each other.

  1. A226547E01
    Align the hole in the lever of the tensioner with the hole in the tensioner body as shown in the illustration, and then insert a pin with a diameter of 1.27 mm (0.0500 in.) into the hole.
    Text in Illustration 
    *1
    Lever Hole
    *2
    Tensioner Hole

  1. A072945E01
    Turn the crankshaft clockwise and align the notch with the "0" timing mark of the timing chain cover.

  1. A224739
    Remove the 2 bolts and chain tensioner.

    NOTICE:
    Do not drop the No. 1 chain tensioner assembly or bolts into the timing chain cover.


43. DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 1)

  1. A226507E01
    Turn the crankshaft clockwise until it is in the position shown in the illustration so that there is some slack in the chain between the banks.

    HINT:
    When turning the crankshaft, engine oil may spray out of the oil holes.

    CAUTION:
    As the camshafts turn suddenly, do not touch the camshafts or camshaft timing gears.

  1. A226508E01
    Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain can be removed easily.

    HINT:
    When turning the crankshaft, engine oil may spray out of the oil holes.

  1. A224759
    Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

    CAUTION:
    As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.


44. REMOVE CAMSHAFT BEARING CAP (for Bank 1)

  1. A225726E01
    Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install bolts and washers for temporary installation of the camshaft housing in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    *1
    Bolt
    *2
    Washer
    *a
    Part Removal
    *b
    Installation of Bolts and Washers for Temporary Installation of camshaft housing

    HINT:
    1. Arrange the removed parts so that they can be reinstalled in their original locations.
    2. Part number of bolt for temporary installation of camshaft housing: 91551-G0845 (quantity: 8)
    3. Part number of washer for temporary installation of camshaft housing: 90201-12028 (quantity: 16)

    NOTICE:
    1. Do not install the bearing caps when installing bolts and washers for temporary installation of the camshaft housing.
    2. Be sure to follow the numerical order when performing this procedure.
    3. Do not allow bolts and washers for temporary installation of the camshaft housing to contact the camshaft.
    4. Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.


45. REMOVE NO. 2 CAMSHAFT

  1. A224761
    Remove the bolt of the No. 2 chain tensioner assembly.

  1. A224769
    Remove the No. 2 chain tensioner assembly while lifting up the No. 2 camshaft.

  1. A224763
    While lifting up the No. 2 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


46. REMOVE CAMSHAFT
  1. Lift up the rear of the camshaft so that it is at an angle.

  1. A224767
    Remove the chain from the camshaft timing gear and pull out the camshaft and No. 2 chain towards the rear of the vehicle to remove them.

    NOTICE:
    Do not drop the chain into the gap between the engine and cover.

  1. A224765
    Suspend the chain with a string or equivalent.


47. DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 2)

  1. A072945E01
    Turn the crankshaft counterclockwise and align the notch with the "0" timing mark of the timing chain cover.

  1. A224760
    Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

    CAUTION:
    As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.


48. REMOVE CAMSHAFT BEARING CAP (for Bank 2)

  1. A225727E01
    Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install bolts and washers for temporary installation of the camshaft housing in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    *1
    Bolt
    *2
    Washer
    *a
    Part Removal
    *b
    Installation of Bolts and Washers for Temporary Installation of camshaft housing

    HINT:
    1. Arrange the removed parts so that they can be reinstalled in their original locations.
    2. Part number of bolt for temporary installation of camshaft housing: 91551-G0845 (quantity: 8)
    3. Part number of washer for temporary installation of camshaft housing: 90201-12028 (quantity: 16)

    NOTICE:
    1. Do not install the bearing caps when installing bolts and washers for temporary installation of the camshaft housing.
    2. Be sure to follow the numerical order when performing this procedure.
    3. Do not allow bolts and washers for temporary installation of the camshaft housing to contact the camshaft.
    4. Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.


49. REMOVE NO. 4 CAMSHAFT

  1. A224762
    Remove the bolt of the No. 3 chain tensioner assembly.

  1. A224770
    Remove the No. 3 chain tensioner assembly while lifting up the No. 4 camshaft.

  1. A224764
    While lifting up the No. 4 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


50. REMOVE NO. 3 CAMSHAFT
  1. Lift up the rear of the camshaft so that it is at an angle.

  1. A224768
    Remove the chain from the camshaft timing gear and pull out the No. 3 camshaft and No. 2 chain towards the rear of the vehicle to remove them.

    NOTICE:
    Do not drop the chain into the gap between the engine and cover.

  1. A224766
    Suspend the chain with a string or equivalent.


51. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.

  1. A227959E01
    Remove the flange bolt and camshaft timing gear assembly.
    Text in Illustration 
    *1
    Do not remove
    *2
    Straight Pin
    *3
    Flange Bolt

    NOTICE:
    1. Do not remove the other 3 bolts.
    2. If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.


52. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.

  1. A227960E01
    Remove the flange bolt and camshaft timing exhaust gear assembly.
    Text in Illustration 
    *1
    Do not remove
    *2
    Straight Pin
    *3
    Flange Bolt

    NOTICE:
    1. Be sure not to remove the other 4 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.

← REMOVAL (Aug 2013 – Jul 2014)INSTALLATION (Aug 2013 – Jul 2014) →