2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

C1681 Front Camera Feedback Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

DTC C1681 is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the front television camera assembly to the parking assist ECU.
DTC C1682 is stored if the parking assist ECU judges as a result of its self check that there is a problem with the current supplied from the front television camera assembly connected to the parking assist ECU.
DTC Code
DTC Detection Condition
Trouble Area
C1681
Front television camera power supply failure
  1. Harness or connector
  2. Front television camera assembly
  3. Parking assist ECU
C1682
An open or short in the front television camera signal circuit

WIRING DIAGRAM

E285856E01

INSPECTION PROCEDURE

NOTICE:
  1. When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (Click here).
  2. Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as wide view front monitor system may be needed (Click here).


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC C1681 and C1682 are not output
    A
    DTC C1681 and/or C1682 is output
    B



B
Go to step 2
A

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY AND BODY GROUND)
  1. Disconnect the I6 and I7 parking assist ECU connectors.

  1. Disconnect the A52 front television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I7-36 (BCV-) - A52-4 (BCV-)
    Always
    Below 1 Ω
    I7-12 (BCV+) - A52-2 (BCV+)
    Always
    Below 1 Ω
    I7-35 (BGND) - A52-3 (BGND)
    Always
    Below 1 Ω
    I7-11 (BCB+) - A52-1 (BCB+)
    Always
    Below 1 Ω
    I7-36 (BCV-) - Body ground
    Always
    10 kΩ or higher
    I7-12 (BCV+) - Body ground
    Always
    10 kΩ or higher
    I7-35 (BGND) - Body ground
    Always
    10 kΩ or higher
    I7-11 (BCB+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK PARKING ASSIST ECU (BCB+, BGND)

  1. E245958E30
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I7-35 (BGND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I7-11 (BCB+) - I7-35 (BGND)
    Engine switch on (IG), wide view front and side monitor switch on
    5.5 to 7.05 V

Text in Illustration 
*a
Component with harness connected
(Parking Assist ECU)
Result 
Proceed to
Result
OK
A
NG (for LHD)
B
NG (for RHD)
C


B
REPLACE PARKING ASSIST ECU (Click here)

C
REPLACE PARKING ASSIST ECU (Click here)
A


4. CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

  1. Measure the resistance according to the value(s) in the table below.E245725E29

    Text in Illustration 
    *a
    Component with harness connected
    (Parking Assist ECU)
    *b
    Waveform A
    *c
    Waveform B
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -

    HINT:
    1. A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
    2. The video waveform changes according to the image sent by the front television camera assembly.

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    I7-12 (BCV+) - I7-35 (BGND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    1. Waveform A: Engine switch on (IG), wide view front and side monitor switch on and camera lens is not covered, displaying an image
    2. Waveform B: Engine switch on (IG), wide view front and side monitor switch on and camera lens is covered, blacking out the screen

Result 
Proceed to
Result
OK (for LHD)
A
OK (for RHD)
B
NG
C


B
REPLACE PARKING ASSIST ECU (Click here)

C
REPLACE FRONT TELEVISION CAMERA ASSEMBLY (Click here)
A

REPLACE PARKING ASSIST ECU (Click here)


← DIAGNOSTIC TROUBLE CODE CHART (from Aug 2014)C1681 Front Camera Feedback Malfunction (+ C1682) (from Aug 2014) →