2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. REMOVE DOOR SCUFF PLATE ASSEMBLY LH (for LHD)

B238732E01
  1. Put protective tape around the door scuff plate.

  1. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


2. REMOVE DOOR SCUFF PLATE ASSEMBLY RH (for RHD)

HINT:
Use the same procedure described for the LH side.


3. REMOVE COWL SIDE TRIM BOARD LH (for LHD)

B238734
  1. Remove the clip.

  1. Detach the clip and claw and remove the cowl side trim board.


4. REMOVE COWL SIDE TRIM BOARD RH (for RHD)

HINT:
Use the same procedure described for the LH side.


5. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

B356218
  1. for LHD:

    1. Remove the screw.

    2. Detach the 2 clips and 2 guides and remove the No. 1 instrument panel under cover.

    3. Disconnect each connector.

  1. B298554
    for RHD:

    1. Remove the screw.

    2. Detach the 3 clips and 2 guides and remove the No. 1 instrument panel under cover.

    3. Disconnect each connector.


6. REMOVE INSTRUMENT SIDE PANEL LH (for LHD)

B238205E01
  1. Put protective tape around the instrument side panel.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel.


7. REMOVE INSTRUMENT SIDE PANEL RH (for RHD)

B238212E01
  1. Put protective tape around the instrument side panel.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 5 clips, claw, and 3 guides.

  1. Disconnect the connector and remove the instrument side panel.


8. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)

B238207E01
  1. Put protective tape around the instrument cluster finish panel ornament.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 3 clips and remove the instrument cluster finish panel ornament.


9. REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

B238239
  1. Detach the 4 clips.

  1. Disconnect each connector and remove the instrument panel finish plate garnish.


10. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

B238214
  1. Detach the 4 clips.

  1. Disconnect each connector and remove the instrument panel finish panel.


11. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

B239280E01
  1. Using a screwdriver, detach the 2 claws and open the cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. B243715
    w/o Knee Airbag:

    1. Remove the 2 bolts <C>.

    2. Detach the 7 clips.

    3. Disconnect each connector and each cable and remove the lower instrument panel finish panel.

  1. B238216
    w/ Knee Airbag:

    1. Remove the 2 bolts <C>.

    2. Detach the 14 clips.

    3. Disconnect each connector and each cable and remove the lower instrument panel finish panel.


12. REMOVE TURN SIGNAL FLASHER ASSEMBLY

  1. E198213
    Disconnect the connector.

  1. Remove the bolt and turn signal flasher.

← REMOVAL (Aug 2013 – Jul 2014)INSTALLATION (Aug 2013 – Jul 2014) →