REMOVAL
Removal / installation · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
- Use the same procedure for RHD and LHD vehicles.
| 1. REMOVE DOOR SCUFF PLATE ASSEMBLY LH (for LHD) |
![]() ![]() |
Put protective tape around the door scuff plate.
Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1
Protective Tape
| 2. REMOVE DOOR SCUFF PLATE ASSEMBLY RH (for RHD) |
- HINT:
- Use the same procedure described for the LH side.
| 3. REMOVE COWL SIDE TRIM BOARD LH (for LHD) |
![]() ![]() |
Remove the clip.
Detach the clip and claw and remove the cowl side trim board.
| 4. REMOVE COWL SIDE TRIM BOARD RH (for RHD) |
- HINT:
- Use the same procedure described for the LH side.
| 5. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() ![]() |
for LHD:
Remove the screw.
Detach the 2 clips and 2 guides and remove the No. 1 instrument panel under cover.
Disconnect each connector.
for RHD:

Remove the screw.
Detach the 3 clips and 2 guides and remove the No. 1 instrument panel under cover.
Disconnect each connector.
| 6. REMOVE INSTRUMENT SIDE PANEL LH (for LHD) |
![]() ![]() |
Put protective tape around the instrument side panel.
Text in Illustration *1
Protective Tape
Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel.
| 7. REMOVE INSTRUMENT SIDE PANEL RH (for RHD) |
![]() ![]() |
Put protective tape around the instrument side panel.
Text in Illustration *1
Protective Tape
Using a moulding remover, detach the 5 clips, claw, and 3 guides.
Disconnect the connector and remove the instrument side panel.
| 8. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD) |
![]() ![]() |
Put protective tape around the instrument cluster finish panel ornament.
Text in Illustration *1
Protective Tape
Using a moulding remover, detach the 3 clips and remove the instrument cluster finish panel ornament.
| 9. REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD) |
![]() ![]() |
Detach the 4 clips.
Disconnect each connector and remove the instrument panel finish plate garnish.
| 10. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
![]() ![]() |
Detach the 4 clips.
Disconnect each connector and remove the instrument panel finish panel.
| 11. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
![]() ![]() |
Using a screwdriver, detach the 2 claws and open the cover.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1
Protective Tape
w/o Knee Airbag:

Remove the 2 bolts <C>.
Detach the 7 clips.
Disconnect each connector and each cable and remove the lower instrument panel finish panel.
w/ Knee Airbag:

Remove the 2 bolts <C>.
Detach the 14 clips.
Disconnect each connector and each cable and remove the lower instrument panel finish panel.
| 12. REMOVE TURN SIGNAL FLASHER ASSEMBLY |
Disconnect the connector.

Remove the bolt and turn signal flasher.









