2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

OPERATION CHECK

Troubleshooting · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


CHECK NAVIGATION SYSTEM NORMAL CONDITION
  1. If the cause of a symptom is any of the following, the corresponding symptom is normal; it is not a malfunction.

    Symptom
    Answer
    A longer route than expected is chosen.
    Depending on the road conditions, the navigation receiver assembly may determine that a longer route is quicker.
    Even when distance priority is high, the shortest route is not shown.
    Some routes may not be advised due to safety concerns.
    When the vehicle is put into motion immediately after the engine starts, the navigation system deviates from the correct position.
    If the vehicle starts before the navigation system activates, the system may not react.
    When driving on certain types of roads, especially new roads, the vehicle position deviates from the correct position.
    When the vehicle is driving on new roads not available on the solid state drive, the system attempts to match it to another nearby road, causing the position mark to deviate.

  2. I100066
    The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor, speed sensor or navigation receiver assembly.

    1. The current position mark may be displayed on a nearby parallel road.

    2. I100067
      Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.

    3. I100068
      When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.

    4. I100069
      When the vehicle is carried, such as on a ferry, and the vehicle itself is not driving, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by the GPS.

    5. I100070
      When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.

    6. I100071
      When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees), the current vehicle position mark may deviate from the correct position.

    7. I100072
      When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.

    8. E106418
      When the engine switch is turned to on (ACC or IG) and the vehicle is turned on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.

    9. I100074
      When the vehicle travels on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.

    10. I100075
      When the tires are changed, the current vehicle position mark may deviate from the correct position.

      HINT:
      1. A change in tire diameter may cause a speed sensor error.
      2. Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.


CHECK PANEL & STEERING SWITCH

HINT:
  1. The navigation receiver assembly panel switches and steering switches are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E274396
    Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.

  4. E225786E01
    Panel & Steering Switch Check Mode
    Screen Description 
    Display
    Content
    *a: Switch condition
    "Pushed" is displayed when any switch is pushed
    *b: Number of switches pushed
    1. Number of switches pushed at once is displayed
    2. If more than 3 switches are pushed at once, "More than 3" is displayed
    *c: Rotary switch direction
    Direction of rotary switch is displayed

    1. Operate each switch and check that the switch conditions are correctly displayed.

      NOTICE:
      When the "MENU" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.


CHECK TOUCH SWITCH

HINT:
  1. The touch switches on the screen are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E274397
    Select "Touch Switch" from the "Function Check/Setting I" screen.

  4. Touch Switch Check

    1. E176521
      Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

      HINT:
      1. A "+" mark is displayed where the display is touched.
      2. The "+" mark remains on the display even after the finger is removed.


CHECK MIC & VOICE RECOGNITION

HINT:
  1. The microphone and microphone input level are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E274398
    Select "Mic&Voice Recognition" from the "Function Check/Setting I" screen.

  4. E187218E19
    Microphone&Voice Recognition Check
    Screen Description 
    Display
    Content
    *a: Microphone input level meter
    Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.
    *b: Recording switch
    Starts recording.
    *c: Stop switch
    Stops recording and playing.
    *d: Play switch
    Plays the recorded voice.
    *e: Recording indicator
    Comes on while recording.

    1. When speaking into the microphone, check that the microphone input level meter changes according to the input level.

      HINT:
      The microphone is active at all times when this screen is displayed.

    2. Push the recording switch and perform voice recording.

      HINT:
      1. Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
      2. While recording or playing, the switches other than the stop switch cannot be pushed.
      3. When no recording is present, the play switch cannot be pushed.
      4. Recording will stop after 5 seconds or when the stop switch is pushed.

    3. Check that the recording indicator remains on while recording and that the recording can be played normally.


CHECK COLOR BAR

HINT:
  1. The display color on the screen is checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E274399
    Select "Color Bar" from the "Function Check/ Setting I" screen.

  4. E226305
    Color Bar Check Mode

    1. Select a color bar from the "Color Bar Check Mode" screen.

    2. Check the display color.

      HINT:
      1. The entire screen turns to the color or stripe selected.
      2. Touching the display will return to the "Color Bar Check Mode" screen.


CHECK GPS & VEHICLE SENSORS

HINT:
  1. GPS information, vehicle signals and sensor signals are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E274400
    Select "GPS&Vehicle Sensors" from the "Function Check/Setting I" screen.

  4. E225775E01
    GPS Information
    *a: Satellite Information Description 
    Display
    Content
    No.
    Number of the target GPS satellite.
    Elv
    Elevation angle of the target GPS satellite.
    Azm
    Direction of the target GPS satellite
    LVL
    The GPS signal level
    *b: Receiving Condition Description 
    Display
    Content
    P
    The system is using the GPS signal for location.
    T
    The system is tracking the GPS signal for location.
    U
    The system is receiving a GPS signal, but is not using it for location.
    -
    The system cannot receive a GPS signal. (Searching a GPS Signal)
    *c: Measurement Status Description 
    Display
    Content
    OK (H3D)
    High accuracy 3-dimensional location method is being used.
    OK (H2D)
    High accuracy 2-dimensional location method is being used.
    OK (3D)
    3-dimensional location method is being used.
    OK (2D)
    2-dimensional location method is being used
    NG
    Location data cannot be used.
    error
    Reception error has occurred.
    -
    Any other state.
    *d: Position Information Description 
    Display
    Content
    Position
    Latitude and longitude information on the current position is displayed.
    *e: Date information Description 
    Display
    Content
    Date
    The date/time information obtained from GPS signals is displayed in Greenwich Mean Time (GMT).

    1. When the "GPS Information" screen is displayed, check the GPS conditions.

  5. Select "Sensors Check" from the "GPS Information" screen.

  6. E274391E01
    Vehicle Sensors
    Screen Description 
    Display
    Content
    *a: Vehicle signal
    Vehicle speed signal condition is displayed.
    *b: Sensor signal
    Gyro sensor output condition is displayed.

    HINT:
    This screen is updated once per second.


    1. Check all the signals and sensors when vehicle signal information is displayed.

  7. E235422E01
    GPS Time Setting
    Screen Description 
    Display
    Content
    *a: Time display
    Displays the date and time in the device.
    *b: Time setting screen
    Setting is possible only when GPS signals are not being received.
    *c: Cursor movement switch
    Moves the cursor on the date and time setting screen to the right and left.
    *d: Adjustment switch
    Adjusts values of items selected by the cursor.
    *e: OK switch
    Selecting this switch after setting the date and time updates the date and time in the device (only when GPS signals are not received).

  8. When GPS signals are not being received, the date and time in the device can be adjusted.

    HINT:
    1. The G-BOOK system cannot be used in areas where GPS signals are not being received. As a result, when using the G-BOOK system in areas such as indoors, set the GPS time from the GPS time setting screen.
    2. Time setting is possible only when GPS signals are not being received. When the navigation system is receiving GPS signals, priority is given to displaying the time and date received via GPS.


CHECK VEHICLE SIGNAL

HINT:
  1. Vehicle signals received by the navigation receiver assembly are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E274401
    Select "Vehicle Signal" from the "Function Check/Setting I" screen.

  4. E225776
    Vehicle Signal Check Mode
    Screen Description 
    Display
    Content
    Battery
    Battery voltage is displayed.
    IG
    Engine switch ON/OFF state is displayed.
    PKB
    Parking brake ON/OFF state is displayed.
    REV
    Reverse signal ON/OFF state is displayed.
    SPEED
    Vehicle speed is displayed in km/h.
    TAIL
    Tail signal (Light control switch) ON/OFF state is displayed.
    ADIM/TCAN
    Brightness state DIM (with) / BRIGHT (without) is displayed.

    HINT:
    1. Only conditions have inputs are displayed.
    2. This screen displays vehicle signals input to the navigation receiver assembly.


    1. When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.


CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING

HINT:
  1. The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E274402
    Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.

  4. E266888E03
    Hands-Free Voice Quality Setting (Receive/Send Voice Level adjustment)
    Screen Description 
    Display
    Content
    *a: Receive voice level
    Setting for the voice level received from "Bluetooth" compatible phones.
    *b: Send voice level
    Setting for the voice level sent from "Bluetooth" compatible phones.

    NOTICE:
    Sound quality may deteriorate when the receive voice or send voice level is changed more than necessary. For this reason, check that the received voice or sent voice quality is still acceptable after changing this setting.


    1. If the voice level is low, press the up button, and if the voice level is loud, press the down button.

      HINT:
      1. Settings will be applied when the up or down button is selected.
      2. The received voice level adjustment ranges from -5 to +1.
      3. The sent voice level adjustment ranges from -5 to +4.
      4. The initial level is "0".

  5. Hands-Free Voice Quality Setting (Voice Quality Type adjustment)

    1. E274394E01
      If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.
      Text in illustration 
      *a
      Numeric keypad
      *b
      Setting button
      *c
      Reset button

    2. When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

      Settings 
      Parameter
      Target Phenomenon
      Voice Quality Type
      Positive Effect of Changing Voice Quality
      Negative Effect of Changing Voice Quality
      A
      (Noise)
      The change in background noise the other party hears becomes unpleasant.
      1000
      The change in background noise the other party hears is reduced.
      Background noise when not talking becomes large.
      B
      (Noise)
      The volume of the noise the other party hears temporarily becomes large.
      2000
      The temporary noise is reduced.
      The volume of voice may drop temporarily.
      C
      (Echo)
      The other party hears weak echoes.
      0100
      The amount of echo is reduced (low level).
      Sound quality of the other party deteriorates (low level).
      D
      (Echo)
      The other party hears strong echoes.
      0200
      The amount of echo is reduced (high level).
      Sound quality of the other party deteriorates (high level).
      E
      (Voice Quality)
      The other party hears harsh noises.
      0010
      Sound the other party hears becomes soft.
      Sound the other party hears becomes muffled.
      F
      (Voice Quality)
      You hear harsh noises.
      0020
      Sound you hear becomes soft.
      Sound you hear becomes muffled.
      Settings (When Multiple Phenomena Occurred) 
      Parameter
      Target Phenomenon
      Voice Quality Type
      Positive Effect of Changing Voice Quality
      Negative Effect of Changing Voice Quality
      A+C
      The change in background noise the other party hears becomes unpleasant and the other party hears weak echoes.
      1100
      1. The change in background noise the other party hears is reduced.
      2. The amount of echo is reduced (low level).
      1. Background noise when not talking becomes large.
      2. Sound quality of the other party deteriorates (low level).
      A+D
      The change in background noise the other party hears becomes unpleasant and the other party hears strong echoes.
      1200
      1. The change in background noise the other party hears is reduced.
      2. The amount of echo is reduced (high level).
      1. Background noise when not talking becomes large.
      2. Sound quality of the other party deteriorates (high level).
      B+C
      The volume of the noise the other party hears temporarily becomes large and the other party hears weak echoes.
      2100
      1. The temporary noise is reduced.
      2. The amount of echo is reduced (low level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (low level).
      B+D
      The volume of the noise the other party hears temporarily becomes large and the other party hears strong echoes.
      2200
      1. The temporary noise is reduced.
      2. The amount of echo is reduced (high level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (high level).
      C+E
      The other party hears weak echoes and harsh noises.
      0110
      1. The amount of echo is reduced (low level).
      2. Sound the other party hears becomes soft.
      1. Sound quality of the other party deteriorates (low level).
      2. Sound the other party hears becomes muffled.
      C+F
      The other party hears weak echoes and you hear harsh noises.
      0120
      1. The amount of echo is reduced (low level).
      2. Sound you hear becomes soft.
      1. Sound quality of the other party deteriorates (low level).
      2. Sound you hear becomes muffled.

      HINT:
      1. The default value is "0000".
      2. Settings will be applied when the setting button is selected.
      3. If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.
      4. If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.


CLEAR PASSWORD OF EXPORT/IMPORT MEMORY POINT FUNCTION

HINT:
  1. This function allows the initialization of a password which was set on the navigation receiver assembly when exporting/importing memory points.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E229432
    Select "Service Information" from the "Service Menu" screen.

  3. E282961
    Select "Memory point backup" from the "Service Information" screen.

  4. E235720
    Clear backup password

    HINT:
    Depending on the manufacturer, some component names and versions will be displayed differently.


    1. Select "Clear backup password" from the "Memory point backup" screen.


CHECK SOFTWARE ERROR HISTORY

HINT:
This function is used to check the cause when the navigation receiver assembly screen is blacked out.

  1. Check software error history.

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.

    5. When an item is stored for Software Error History, record it before repairing the navigation receiver assembly.

      Software Error History Screen Description 
      Error Description
      Trigger
      Detail
      Software Reset
      Navi Microcomputer
      Hexadecimal Number
      Audio Microcomputer
      CAN Microcomputer
      No Video Signal
      Front Monitor
      Rear Monitor
      MOST Cold Restart
      Always

      HINT:
      1. Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.
      2. If an error that is unsupported by the GTS occurs, a "-" is displayed for the display items.

  2. Clear software error history.

    1. When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (Click here).

      1. Cleared using the GTS.
      2. Cleared using the system check mode screen.
      3. Cleared using the unit check mode screen.


CHECK OPTICAL DISC ERROR HISTORY

HINT:
This function is used to check the cause when an optical disc error occurs.

  1. Check optical disc error history.

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.

    5. When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

      Optical Disc Error History Screen Description 
      Display
      Content
      Error Type
      Displays the type of error.
      Device
      Displays the malfunctioning device.
      Date
      Displays the date and time that the malfunction occurred.
      "Error Type" Screen Description 
      Error Type
      Detection Condition
      Action
      Read Error
      When a disc read error occurs.
      Proceed to next suspected area shown in Problem Symptoms Table (Click here)
      Disc damaged/upside down/dirty
      When it is determined that any of the following is the cause of the disc read error:
      1. The disc cannot be read.
      2. The disc cannot be read because of dirt or scratches.
      3. The disc cannot be read because it is inserted upside down.
      Cannot determine disc type
      An unsuitable disc is inserted.
      DPS error
      When an error occurs while decoding MP3/WMA files.
      Some files are corrupt
      1. When MP3/WMA files cannot be played back because they are unsupported.
      2. Even though the file extensions are MP3 or WMA files cannot be played back because the header information cannot be read.
      Some files cannot be found
      1. When a disc without music data is played back.
      2. When there are no playable MP3/WMA files.
      Copy protection violation
      When a file with copyright protection that cannot be played back is played back.
      "Device" Screen Description 
      Device
      Content
      DVD-P
      Navigation receiver assembly
      CD-P
      Not available
      R-Seat DVD-P
      Not available

      HINT:
      1. Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.
      2. If an error that is unsupported by the GTS occurs, a "-" or blank is displayed for the display items.

  2. Clear optical disc error history.

    1. When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (Click here).

      1. Cleared using the GTS.
      2. Cleared using the system check mode screen.
      3. Cleared using the unit check mode screen.


MAP INFORMATION

HINT:
This function is used to check the map version of the navigation system and the end date of the map update service.

  1. Check map information.

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Navigation System / Utility / Map Information.

    5. Check the map version and the end date of the map update service.

← HOW TO PROCEED WITH TROUBLESHOOTING (from Aug 2014)OPERATION CHECK (from Aug 2014) →