2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Power Source Mode does not Change to ON (ACC)

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the engine switch is pushed with the key in the cabin, the power management control ECU receives signals to switch the power source mode.

HINT:
To allow use of the intelligent tester to inspect the push-button start function when the engine switch is off, repeatedly open and close any of the doors. Repeatedly opening and closing a door establishes communication between the intelligent tester and power management control ECU (opening and closing a door can also be simulated by operating a door courtesy light switch).


WIRING DIAGRAM

Refer to "Power Source Mode does not Change to on (IG and ACC)" (Click here).

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)

  1. A207890E06
    Disconnect the G51 power management control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G51-2 (AM21) - Body ground
    Always
    9.5 to 14 V
    G51-1 (AM22) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Disconnect the G51 power management control ECU connector.

  1. A207890E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G51-6 (GND) - Body ground
    Always
    Below 1 Ω
    G51-5 (GND2) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)

  1. B231373E06
    Remove the driver side junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2A-48 - 2D-4
    20°C (68°F)
    101.25 to 123.75 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Driver Side Junction Block Assembly)



NG
REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
OK


4. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the G51 power management control ECU connector.

  1. Disconnect the 2A driver side junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G51-19 (ACCD) - 2A-48
    Always
    Below 1 Ω
    G51-19 (ACCD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BODY GROUND)
  1. Disconnect the 2D driver side junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2D-4 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK POWER MANAGEMENT CONTROL ECU

  1. Connect the power management control ECU connector.C182533E16

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    -
    -

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G51-19 (ACCD) - Body ground
    Engine switch off
    Below 1 V
    Engine switch on (ACC)
    ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK


7. CONFIRMATION TEST
  1. Check that the power source mode changes to on (ACC) and on (IG) when operating the engine switch.

    OK:
    The power source mode changes to on (ACC) and on (IG) in response to the operation of the engine switch.



NG
CHECK RELAY CONTACT SIDE CIRCUIT
OK

USE SIMULATION METHOD TO CHECK (Click here)


← Power Source Mode does not Change to ON (IG) (from Aug 2014)Power Source Mode does not Change to ON (ACC) (from Aug 2014) →