Power Source Mode does not Change to ON (IG and ACC)
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
When the engine switch is pushed with the key in the cabin, the power management control ECU receives signals to switch the power source mode.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
- Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
| 1. CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU) |
Disconnect the G51 power management control ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
G51-2 (AM21) - Body ground
Always
9.5 to 14 V
G51-1 (AM22) - Body ground
Text in Illustration *a
Rear view of wire harness connector
(to Power Management Control ECU)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND) |
Disconnect the G51 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
G51-6 (GND) - Body ground
Always
Below 1 Ω
G51-5 (GND2) - Body ground
Text in Illustration *a
Rear view of wire harness connector
(to Power Management Control ECU)
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (KEY CERTIFI WAIT T-OUT) |
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
- HINT:
- When using the intelligent tester with the engine switch off, turn any of the door courtesy light switches on and off repeatedly at intervals of 1.5 seconds or less until communication between the tester and vehicle starts.
Enter the following menus: Body / Power Source Control / Data List.
Read the Data List and check that "No" is displayed 1 second after turning the engine switch from off to on (IG).
Power Source Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Key Certifi Wait T-Out
Key certification waiting timed out / Yes or No
Yes: Key certification waiting timed out
No: Key certification completed within specified time
-
- OK:
- "No" is displayed 1 second after turning the engine switch from off to on (IG).
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (START SWITCH 1, 2) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
According to the display on the intelligent tester, read the Data List.
Power Source Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Start Switch1
Start Switch 1 / ON or OFF
ON: Engine switch pushed
OFF: Engine switch not pushed
-
Start Switch2
Start Switch 2 / ON or OFF
ON: Engine switch pushed
OFF: Engine switch not pushed
-
- OK:
- The display changes in response to the operation of the engine switch.
|
|
||||
| OK | |
| 5. CHECK POWER MANAGEMENT CONTROL ECU |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
Read the Data List and check that the display changes according to the changes in the power source mode when the engine switch is pushed.
Power Source Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Power Supply Condition
Power Supply Condition / IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
IG2 ON: IG2 relay on
ST ON: ST request signal on
All OFF: All relays off
IG1 ON: IG1 relay on
ACC ON: ACC relay on
-
- OK:
- Display changes according to the changes in the power source mode when the engine switch is pushed.
Measure the voltage according to the value(s) in the table below.


Text in Illustration *a
Component with harness connected
(Power Management Control ECU)
-
-
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G51-20 (IG1D) - Body ground
Engine switch off
Below 1 V
Engine switch on (ACC)
Engine switch on (IG)
((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
G50-8 (IG2D) - Body ground
Engine switch off
Below 1 V
Engine switch on (ACC)
Engine switch on (IG)
((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
G51-19 (ACCD) - Body ground
Engine switch off
Below 1 V
Engine switch on (ACC)
((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
Engine switch on (IG)
((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
|
|
||||
| OK | |
| 6. CONFIRMATION TEST |
Check that the power source mode changes to on (ACC) and on (IG) when operating the engine switch.
- OK:
- The power source mode changes to on (ACC) and on (IG) in response to the operation of the engine switch.
|
|
||||
| OK | ||
| ||
| 7. INSPECT ENGINE SWITCH |
Remove the engine switch.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
7 (SS1) - 5 (GND)
Engine switch not pushed
10 kΩ or higher
Engine switch pushed
Below 1 Ω
2 (SS2) - 5 (GND)
Engine switch not pushed
10 kΩ or higher
Engine switch pushed
Below 1 Ω
Text in Illustration *a
Component without harness connected
(Engine Switch)
- HINT:
- for 1GR-FE (LHD): Click here.
- for 1GR-FE (RHD): Click here.
- for 2TR-FE: Click here.
- for 1KD-FTV (LHD): Click here.
- for 1KD-FTV (RHD): Click here.
- for 1GR-FE (LHD): Click here.
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE SWITCH) |
Disconnect the G51 power management control ECU connector.
Disconnect the G36 engine switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G51-17 (SSW2) - G36-2 (SS2)
Always
Below 1 Ω
G51-18 (SSW1) - G36-7 (SS1)
G51-17 (SSW2) - Body ground
Always
10 kΩ or higher
G51-18 (SSW1) - Body ground
G36-5 (GND) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 9. CHECK FOR DTC |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Power Source / DTC.
Read the DTCs.
Enter the following menus: Body / Entry&Start / DTC.
Read the DTCs.
Result Result
Proceed to
None of the following DTCs are output:
B2785 Communication Malfunction between ECUs Connected by LIN
B2287 LIN Communication Master Malfunction
B2784 Antenna Coil Open/Short
A
DTC B2287 is output but B2785 is not
B
A DTC other than B2287 is output.
C
|
|
||||
|
|
||||
| A | ||
| ||
