2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0489 Exhaust Gas Recirculation Control Circuit Low

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The EGR system recirculates exhaust gases in a way that suits every driving condition. The recirculated gas mixes with intake air. Therefore, the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emission.
In order to increase EGR circulation efficiency, the ECM adjusts the lift amount of the EGR valve and the throttle valve angle.
P0489 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
5 seconds after engine is started
Open or short in electric vacuum regulating valve assembly circuit for 5 seconds or more (1 trip detection logic).
  1. Electric vacuum regulating valve assembly
  2. Open or short in electric vacuum regulating valve assembly circuit
  3. ECM
P0490 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
5 seconds after engine is started
Open or short in electric vacuum regulating valve assembly circuit for 5 seconds or more (1 trip detection logic).
  1. Electric vacuum regulating valve assembly
  2. Open or short in electric vacuum regulating valve assembly circuit
  3. ECM
Related Data List 
DTC No.
Data List
P0489
  1. Actual EGR Valve Pos.
  2. Target EGR Position
P0490

WIRING DIAGRAM

Refer to DTC P0400 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. INSPECT ELECTRIC VACUUM REGULATING VALVE ASSEMBLY
  1. Inspect the electric vacuum regulating valve assembly (Click here).



NG
Go to step 5
OK


2. CHECK TERMINAL VOLTAGE (POWER SOURCE)

  1. A199385E05
    Disconnect the electric vacuum regulating valve assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C76-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to electric vacuum regulating valve assembly)

  1. Reconnect the electric vacuum regulating valve assembly connector.



NG
Go to step 6
OK


3. CHECK HARNESS AND CONNECTOR (ELECTRIC VACUUM REGULATING VALVE ASSEMBLY - ECM)
  1. Disconnect the electric vacuum regulating valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C76-2 - C93-9 (EGR)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C76-2 or C93-9 (EGR) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the electric vacuum regulating valve assembly connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


4. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7
5. REPLACE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY
  1. Replace the electric vacuum regulating valve assembly (Click here).



NEXT
Go to step 7
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.

    HINT:
    If the voltage at the electric vacuum regulating valve assembly connector is not 11 to 14 V, repair or replace the harness and connector between the electric vacuum regulating valve assembly and the EFI relay (including the EFI No. 2 fuse).


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine.

  1. Idle the engine for 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance (from Aug 2014)P0489 Exhaust Gas Recirculation Control Circuit Low (+ P0490) (from Aug 2014) →