B27A5 Open in Front Floor Electrical Key Oscillator Circuit
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The certification ECU generates a request signal and transmits the signal to the indoor No. 1 electrical key antenna (front floor). The indoor No. 1 electrical key antenna (front floor) detects that the electrical key is inside the vehicle and transmits the request signal received from the certification ECU. DTC B27A5 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and indoor No. 1 electrical key antenna (front floor) (CLG5 - CLG3, CG5B - CLGB).| DTC Code |
DTC Detection Condition |
Trouble Area |
| B27A5 |
An open circuit is detected in the circuit between the certification ECU and indoor No. 1 electrical key antenna (front floor) (CLG5 - CLG3, CG5B - CLGB). |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
- Before replacing the certification ECU, refer to the Service Bulletin.
- The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
| 1. CHECK CONNECTOR CONNECTION |
Turn the engine switch off.
Check that the connectors are properly connected to the certification ECU and indoor No. 1 electrical key antenna (front floor).
- OK:
- Connectors are properly connected.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (INDOOR NO. 1 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU) |
Disconnect the i1 antenna connector.
Disconnect the G38 ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
i1-1 (CLG3) - G38-7 (CLG5)
Always
Below 1 Ω
i1-3 (CLGB) - G38-8 (CG5B)
Always
Below 1 Ω
G38-7 (CLG5) - Body ground
Always
10 kΩ or higher
G38-8 (CG5B) - Body ground
Always
10 kΩ or higher
G38-15 (E) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK CERTIFICATION ECU |
Measure the voltage according to the value(s) in the table below.


Text in Illustration *a
Component with harness connected
(Certification ECU)
-
-
- OK:
Tester Connection
Switch Condition
Specified Condition
G38-7 (CLG5) - G38-15 (E)
Engine switch off, all doors closed, key not in cabin and lock sensor off → on
No pulse generation → Pulse generation
G38-8 (CG5B) - G38-15 (E)
Engine switch off, all doors closed, key not in cabin and lock sensor off → on
No pulse generation → Pulse generation
|
|
||||
| OK | |
| 4. REPLACE INDOOR NO. 1 ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR) |
Temporarily replace the indoor No. 1 electrical key antenna (front floor) with a new or normally functioning one (Click here).
| NEXT | |
| 5. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B27A5 is not output.
|
|
||||
| OK | ||
| ||
