2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B27A6 Open in Rear Floor Electrical Key Oscillator Circuit

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The certification ECU generates a request signal and transmits the signal to the indoor No. 2 electrical key antenna (rear floor). The indoor No. 2 electrical key antenna (rear floor) detects that the electrical key is inside the vehicle and transmits the request signal received from the certification ECU. DTC B27A6 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and indoor No. 2 electrical key antenna (rear floor) (CLG6 - CLG4, CG6B - CLGB).
DTC Code
DTC Detection Condition
Trouble Area
B27A6
An open circuit is detected in the circuit between the certification ECU and indoor No. 2 electrical key antenna (rear floor) (CLG6 - CLG4, CG6B - CLGB).
  1. Harness or connector
  2. Indoor No. 2 electrical key antenna (rear floor)
  3. Certification ECU

WIRING DIAGRAM

B243942E01

INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Before replacing the certification ECU, refer to the Service Bulletin.


1. CHECK CONNECTOR CONNECTION
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the certification ECU and indoor No. 2 electrical key antenna (rear floor).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2. CHECK HARNESS AND CONNECTOR (INDOOR NO. 2 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
  1. Disconnect the R14*1 or s1*2 antenna connector.

    1. *1: for 5 Door
    2. *2: for 3 Door

  1. Disconnect the G38 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 5 Door 
    Tester Connection
    Condition
    Specified Condition
    R14-1 (CLG4) - G38-24 (CLG6)
    Always
    Below 1 Ω
    R14-2 (CLGB) - G38-25 (CG6B)
    Always
    Below 1 Ω
    G38-24 (CLG6) - Body ground
    Always
    10 kΩ or higher
    G38-25 (CG6B) - Body ground
    Always
    10 kΩ or higher
    G38-15 (E) - Body ground
    Always
    Below 1 Ω
    for 3 Door 
    Tester Connection
    Condition
    Specified Condition
    s1-1 (CLG4) - G38-24 (CLG6)
    Always
    Below 1 Ω
    s1-2 (CLGB) - G38-25 (CG6B)
    Always
    Below 1 Ω
    G38-24 (CLG6) - Body ground
    Always
    10 kΩ or higher
    G38-25 (CG6B) - Body ground
    Always
    10 kΩ or higher
    G38-15 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK CERTIFICATION ECU

  1. Measure the voltage according to the value(s) in the table below.B224125E18

    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU)
    -
    -

    OK:
    Tester Connection
    Switch Condition
    Specified Condition
    G38-24 (CLG6) - G38-15 (E)
    Engine switch off, all doors closed, key not in cabin and lock sensor off → on
    No pulse generation → Pulse generation
    G38-25 (CG6B) - G38-15 (E)
    Engine switch off, all doors closed, key not in cabin and lock sensor off → on
    No pulse generation → Pulse generation



NG
REPLACE CERTIFICATION ECU
OK


4. REPLACE INDOOR NO. 2 ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)
  1. Temporarily replace the indoor No. 2 electrical key antenna (rear floor) with a new or normally functioning one (Click here).


NEXT


5. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B27A6 is not output.



NG
REPLACE CERTIFICATION ECU
OK

END (INDOOR NO. 2 ELECTRICAL KEY ANTENNA ASSEMBLY IS DEFECTIVE)


← B27A5 Open in Front Floor Electrical Key Oscillator Circuit (from Aug 2014)B27A6 Open in Rear Floor Electrical Key Oscillator Circuit (from Aug 2014) →