2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

U0100 Lost Communication with ECM / PCM "A"

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

DTC Code
DTC Detection Condition
Trouble Area
U0100
There is no communication from the ECM.
  1. Power source or inside ECM
  2. ECM CAN main wire or connector
  3. ECM

WIRING DIAGRAM

C217262E07
C217262E08

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM CAN MAIN WIRE)

  1. Disconnect the G56*1 or G57*2 ECM connector.

    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV
    C217353E01

Text in Illustration 
*A
for 1GR-FE
*B
for 1KD-FTV
*a
Front view of wire harness connector
(to ECM)
-
-
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE 
    Tester Connection
    Switch Condition
    Specified Condition
    G56-34 (CANP) - G56-33 (CANN)
    Engine switch off
    108 to 132 Ω
    for 1KD-FTV 
    Tester Connection
    Switch Condition
    Specified Condition
    G57-20 (CANP) - G57-21 (CANN)
    Engine switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE ECM CAN MAIN WIRE OR CONNECTOR (CANP, CANN)
OK


3. CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. for 1GR-FE:

    1. Connect the cable to the negative (-) battery terminal.C217328E04

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to ECM)
      -
      -

    2. Disconnect the C36, C37 and G55 ECM connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      C36-12 (E1) - Body ground
      Always
      Below 1 Ω
      C37-14 (E01) - Body ground
      Always
      Below 1 Ω
      C37-15 (E02) - Body ground
      Always
      Below 1 Ω
      C37-10 (ME01) - Body ground
      Always
      Below 1 Ω
      G55-12 (EC) - Body ground
      Always
      Below 1 Ω

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      G55-24 (BATT) - Body ground
      Always
      11 to 14 V
      G55-23 (+B2) - Body ground
      Battery positive (+) voltage applied to terminal G55-9 (MREL)
      11 to 14 V
      G55-22 (+B) - Body ground
      Battery positive (+) voltage applied to terminal G55-9 (MREL)
      11 to 14 V

  1. for 1KD-FTV:

    1. Connect the cable to the negative (-) battery terminal.C289505E01

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to ECM)
      -
      -

    2. Disconnect the G57, G58 and C93 ECM connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      C93-1 (E1) - Body ground
      Always
      Below 1 Ω
      C93-12 (E01) - Body ground
      Always
      Below 1 Ω
      C93-13 (E02) - Body ground
      Always
      Below 1 Ω
      C93-8 (ME01) - Body ground
      Always
      Below 1 Ω
      G57-11 (EC) - Body ground
      Always
      Below 1 Ω

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      G57-23 (BATT) - Body ground
      Always
      11 to 14 V
      G57-17 (+B2) - Body ground
      Battery positive (+) voltage applied to terminal G58-11 (MREL)
      11 to 14 V
      G57-24 (+B) - Body ground
      Battery positive (+) voltage applied to terminal G58-11 (MREL)
      11 to 14 V

Result 
Result
Proceed to
OK (for 1GR-FE)
A
OK (for 1KD-FTV)
B
NG
C


B
REPLACE ECM (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)


← U0100 Lost Communication with ECM / PCM "A" (Aug 2013 – Jul 2014)U0104 Lost Communication with Driving Support ECU (Aug 2013 – Jul 2014) →