C1622 Open or Short Circuit in Back Camera Signal
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
This DTC is stored if the radio and display receiver assembly judges as a result of its self check that the signals or signal lines between the radio and display receiver assembly and the rear television camera assembly are not normal.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1622 |
Open or Short Circuit in television camera signal |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
No DTC is output
A
DTC is output
B
|
|
||||
| A | ||
| ||
| 2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY) |
Disconnect the H50 radio and display receiver assembly connector.
Disconnect the X9*1 or v2*2 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- w/ Tire Carrier:
Tester Connection
Condition
Specified Condition
H50-11 (CA+) - X9-6 (CB+)
Always
Below 1 Ω
H50-12 (V+) - X9-3 (CV+)
Always
Below 1 Ω
H50-23 (CGND) - X9-5 (CGND)
Always
Below 1 Ω
H50-24 (V-) - X9-2 (CV-)
Always
Below 1 Ω
H50-11 (CA+) - Body ground
Always
10 kΩ or higher
H50-12 (V+) - Body ground
Always
10 kΩ or higher
H50-23 (CGND) - Body ground
Always
10 kΩ or higher
H50-24 (V-) - Body ground
Always
10 kΩ or higher
- w/o Tire Carrier:
Tester Connection
Condition
Specified Condition
H50-11 (CA+) - v2-6 (CB+)
Always
Below 1 Ω
H50-12 (V+) - v2-3 (CV+)
Always
Below 1 Ω
H50-23 (CGND) - v2-5 (CGND)
Always
Below 1 Ω
H50-24 (V-) - v2-2 (CV-)
Always
Below 1 Ω
H50-11 (CA+) - Body ground
Always
10 kΩ or higher
H50-12 (V+) - Body ground
Always
10 kΩ or higher
H50-23 (CGND) - Body ground
Always
10 kΩ or higher
H50-24 (V-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
H50-23 (CGND) - Body ground
Always
Below 1 Ω
H50-24 (V-) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
H50-11 (CA+) - Body ground
Ignition switch ON
5.5 to 7.05 V
| *a |
Component with harness connected (Radio and Display Receiver Assembly) |
| Result |
Proceed to |
| OK |
A |
| NG (w/ Navigation System) |
B |
| NG (w/o Navigation System) |
C |
|
|
||||
|
|
||||
| A | |
| 4. CHECK REAR TELEVISION CAMERA ASSEMBLY |
Using an oscilloscope, check the waveform.


Text in Illustration *a
Component with harness connected
(Radio and Display Receiver Assembly)
*b
Waveform 1
*c
Waveform 2
*d
Synchronized Signal
*e
Video Waveform
-
-
Measurement Condition Item
Content
Tester Connection
H50-12 (V+) - H50-23 (CGND)
Tool Setting
200 mV/DIV., 50 μs/DIV.
Condition
- Waveform 1: Ignition switch ON, camera lens not covered, displaying an image
- Waveform 2: Ignition switch ON, camera lens covered, blacking out screen
- OK:
- Waveform is as shown in illustration.
- HINT:
- The video waveform changes according to the image sent by the rear television camera assembly.
- Waveform 1: Ignition switch ON, camera lens not covered, displaying an image
|
|
||||
| OK | ||
| ||
| 5. REPLACE REAR TELEVISION CAMERA ASSEMBLY |
Replace the rear television camera assembly with a new or normally functioning one.
- w/ Tire Carrier: Click here
- w/o Tire Carrier: Click here
- w/ Tire Carrier: Click here
| NEXT | |
| 6. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
OK
A
NG (w/ Navigation System)
B
NG (w/o Navigation System)
C
|
|
||||
|
|
||||
| A | ||
| ||
