2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

C1622 Open or Short Circuit in Back Camera Signal

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored if the radio and display receiver assembly judges as a result of its self check that the signals or signal lines between the radio and display receiver assembly and the rear television camera assembly are not normal.
DTC Code
DTC Detection Condition
Trouble Area
C1622
Open or Short Circuit in television camera signal
  1. Harness or connector
  2. Rear television camera assembly
  3. Radio and display receiver assembly

WIRING DIAGRAM

E286150E04

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC is output
    B



B
Go to step 2
A

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the H50 radio and display receiver assembly connector.

  1. Disconnect the X9*1 or v2*2 rear television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Tire Carrier:
     
    Tester Connection
    Condition
    Specified Condition
    H50-11 (CA+) - X9-6 (CB+)
    Always
    Below 1 Ω
    H50-12 (V+) - X9-3 (CV+)
    Always
    Below 1 Ω
    H50-23 (CGND) - X9-5 (CGND)
    Always
    Below 1 Ω
    H50-24 (V-) - X9-2 (CV-)
    Always
    Below 1 Ω
    H50-11 (CA+) - Body ground
    Always
    10 kΩ or higher
    H50-12 (V+) - Body ground
    Always
    10 kΩ or higher
    H50-23 (CGND) - Body ground
    Always
    10 kΩ or higher
    H50-24 (V-) - Body ground
    Always
    10 kΩ or higher
    w/o Tire Carrier:
    Tester Connection
    Condition
    Specified Condition
    H50-11 (CA+) - v2-6 (CB+)
    Always
    Below 1 Ω
    H50-12 (V+) - v2-3 (CV+)
    Always
    Below 1 Ω
    H50-23 (CGND) - v2-5 (CGND)
    Always
    Below 1 Ω
    H50-24 (V-) - v2-2 (CV-)
    Always
    Below 1 Ω
    H50-11 (CA+) - Body ground
    Always
    10 kΩ or higher
    H50-12 (V+) - Body ground
    Always
    10 kΩ or higher
    H50-23 (CGND) - Body ground
    Always
    10 kΩ or higher
    H50-24 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

  1. E280624E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H50-23 (CGND) - Body ground
    Always
    Below 1 Ω
    H50-24 (V-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H50-11 (CA+) - Body ground
    Ignition switch ON
    5.5 to 7.05 V

Text in Illustration 
*a
Component with harness connected
(Radio and Display Receiver Assembly)
Result 
Result
Proceed to
OK
A
NG (w/ Navigation System)
B
NG (w/o Navigation System)
C


B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

C
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
A


4. CHECK REAR TELEVISION CAMERA ASSEMBLY

  1. Using an oscilloscope, check the waveform.E275625E13

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)
    *b
    Waveform 1
    *c
    Waveform 2
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -
    Measurement Condition 
    Item
    Content
    Tester Connection
    H50-12 (V+) - H50-23 (CGND)
    Tool Setting
    200 mV/DIV., 50 μs/DIV.
    Condition
    1. Waveform 1: Ignition switch ON, camera lens not covered, displaying an image
    2. Waveform 2: Ignition switch ON, camera lens covered, blacking out screen

    OK:
    Waveform is as shown in illustration.

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. REPLACE REAR TELEVISION CAMERA ASSEMBLY
  1. Replace the rear television camera assembly with a new or normally functioning one.

    1. w/ Tire Carrier: Click here
    2. w/o Tire Carrier: Click here


NEXT


6. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Navigation System)
    B
    NG (w/o Navigation System)
    C



B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

C
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
A

END (REAR TELEVISION CAMERA ASSEMBLY WAS DEFECTIVE)


← DIAGNOSTIC TROUBLE CODE CHART (from Aug 2014)C1622 Open or Short Circuit in Back Camera Signal (from Aug 2014) →