HOW TO PROCEED WITH TROUBLESHOOTING
Troubleshooting · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
- HINT:
- Use the following procedure to troubleshoot the audio and visual system.
- *: Use the GTS.
- Use the following procedure to troubleshoot the audio and visual system.
| 1.VEHICLE BROUGHT TO WORKSHOP |
| |||||
| 2.CUSTOMER PROBLEM ANALYSIS |
- When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
- The following 5 items are important points in problem analysis:
What
Vehicle model, system name
When
Date, time, occurrence frequency
Where
Road conditions
Under what conditions?
Driving conditions, weather conditions
How did it happen?
Problem symptoms
| |||||
| 3.INSPECT BATTERY VOLTAGE |
Measure the battery voltage with the ignition switch off.
- Standard voltage:
- 11 to 14 V
- If the voltage is below 11 V, recharge or replace the battery.
| |||||
| 4.CHECK CABIN |
Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.
- OK:
- Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.
- HINT:
- A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.
- The audio and visual system may not operate normally when the temperature is -20°C (-4°F) or less, or 65°C (149°F) or higher.
- A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.
|
|||||
| |||||
| 5.CHECK CAN COMMUNICATION SYSTEM* |
Check for DTC output.
- for LHD with Entry and Start System: Click here
- for LHD without Entry and Start System: Click here
- for RHD with Entry and Start System: Click here
- for RHD without Entry and Start System: Click here
Result Result
Proceed to
CAN DTCs are not output
A
CAN DTCs are output (for LHD with Entry and Start System)
B
CAN DTCs are output (for LHD without Entry and Start System)
C
CAN DTCs are output (for RHD with Entry and Start System)
D
CAN DTCs are output (for RHD without Entry and Start System)
E
- for LHD with Entry and Start System: Click here
|
|||||
|
|||||
|
|||||
|
|||||
| |||||
| 6.DTC CLEAR* |
Refer to DTC Check/Clear (Click here).
Result Result
Proceed to
DTCs are output
A
DTCs are not output
B
| |||||
| 7.RECHECK FOR DTC* |
Refer to DTC Check/Clear (Click here).
Result Result
Proceed to
DTC is output
A
DTC is not output
B
- HINT:
- Even if the malfunction symptom is not confirmed, check for diagnostic trouble codes. This is because the system stores past diagnostic trouble codes.
- After the check using the GTS, check the "System Check Mode" screen as necessary.
- Check the diagnostic trouble code and inspect the area code indicates.
- Even if the malfunction symptom is not confirmed, check for diagnostic trouble codes. This is because the system stores past diagnostic trouble codes.
|
|||||
| |||||
| 8.DIAGNOSTIC TROUBLE CODE CHART |
Find the output code in Diagnostic Trouble Code Chart (Click here).
- NOTICE:
- The audio and visual system outputs DTCs for the following systems.
- When DTCs other than the codes in Diagnostic Trouble Code Chart for the audio and visual system are output, refer to Diagnostic Trouble Code Chart for the following systems.
- The audio and visual system outputs DTCs for the following systems.
Result Result
Proceed to
DTCs for the Audio and Visual System (w/ Radio and Display Type) are output
A
DTCs for the Rear View Monitor System (w/ Radio and Display Type) are output
B
DTCs for the Rear Seat Entertainment System are output
C
|
||||
|
||||
|
| 9.PROBLEM SYMPTOMS TABLE |
Refer to Problem Symptoms Table (Click here).
Result Result
Proceed to
Fault is not listed in Problem Symptoms Table
A
Fault is listed in Problem Symptoms Table
B
- HINT:
- If the symptom does not recur and no DTC is output, perform the symptom reproduction method (Click here).
|
|||||
| |||||
| 10.CHECK ECU TERMINAL ARRANGEMENT BASED ON MALFUNCTION SYMPTOM |
Refer to Terminals of ECU (Click here).
| |||||
| 11.CHECK CIRCUIT |
Adjust, repair or replace as necessary.
| |||||
| 12.RECHECK FOR DIAGNOSTIC TROUBLE CODE |
- HINT:
- After clearing DTCs, recheck for DTCs.
| |||||
| 13.PERFORM CONFIRMATION TEST |
| |||||