Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
Clutch Switch Circuit
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
While depressing the clutch pedal, the clutch switch sends a signal to terminal 27 (D)*1 or 15 (D)*2 of the ECM. The ECM cancels cruise control when terminal 27 (D)*1 or 15 (CLSW)*2 receives the signal.
*1: for 1GR-FE
*2: for 1KD-FTV
WIRING DIAGRAM
INSPECTION PROCEDURE
1. INSPECT CLUTCH SWITCH ASSEMBLY
for LHD: Remove the clutch switch (Click here ).
for RHD: Remove the clutch switch (Click here ).
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Pushed
Below 1 Ω
Not pushed
10 kΩ or higher
Result
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
Text in Illustration
*1
Pin
*a
Not pushed
*b
Pushed
B
C
A
2. CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - BATTERY)
Disconnect the A43*1 or r3*2 switch connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
for LHD
Tester Connection
Switch Condition
Specified Condition
A43-1 - Body ground
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
for RHD
Tester Connection
Switch Condition
Specified Condition
r3-1 - Body ground
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
Text in Illustration
*A
for LHD
*B
for RHD
*a
Front view of wire harness connector (to Clutch Switch Assembly)
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
3. CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH - ECM)
*1: for LHD
*2: for RHD
*3: for 1GR-FE
*4: for 1KD-FTV
Disconnect the A43*1 or r3*2 switch connector.
Disconnect the C34*3 or C91*4 ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for 1GR-FE (for LHD)
Tester Connection
Condition
Specified Condition
A43-2 - C34-27 (D)
Always
Below 1 Ω
A43-2 - Body ground
Always
10 kΩ or higher
for 1GR-FE (for RHD)
Tester Connection
Condition
Specified Condition
r3-2 - C34-27 (D)
Always
Below 1 Ω
r3-2 - Body ground
Always
10 kΩ or higher
for 1KD-FTV (for LHD)
Tester Connection
Condition
Specified Condition
A43-2 - C91-15 (CLSW)
Always
Below 1 Ω
A43-2 - Body ground
Always
10 kΩ or higher
for 1KD-FTV (for RHD)
Tester Connection
Condition
Specified Condition
r3-2 - C91-15 (CLSW)
Always
Below 1 Ω
r3-2 - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here )