2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

Clutch Switch Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

While depressing the clutch pedal, the clutch switch sends a signal to terminal 27 (D)*1 or 15 (D)*2 of the ECM. The ECM cancels cruise control when terminal 27 (D)*1 or 15 (CLSW)*2 receives the signal.
  1. *1: for 1GR-FE
  2. *2: for 1KD-FTV

WIRING DIAGRAM

E194930E04

INSPECTION PROCEDURE


1. INSPECT CLUTCH SWITCH ASSEMBLY

  1. E200721E01
    for LHD:Remove the clutch switch (Click here).

  1. for RHD:Remove the clutch switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pushed
    Below 1 Ω
    Not pushed
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C
    Text in Illustration 
    *1
    Pin
    *a
    Not pushed
    *b
    Pushed



B
REPLACE CLUTCH SWITCH ASSEMBLY (Click here)

C
REPLACE CLUTCH SWITCH ASSEMBLY (Click here)
A


2. CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - BATTERY)

  1. E200722E01
    Disconnect the A43*1 or r3*2 switch connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    A43-1 - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    r3-1 - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Clutch Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH - ECM)
  1. *1: for LHD
  2. *2: for RHD
  3. *3: for 1GR-FE
  4. *4: for 1KD-FTV
  1. Disconnect the A43*1 or r3*2 switch connector.

  1. Disconnect the C34*3 or C91*4 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE (for LHD) 
    Tester Connection
    Condition
    Specified Condition
    A43-2 - C34-27 (D)
    Always
    Below 1 Ω
    A43-2 - Body ground
    Always
    10 kΩ or higher
    for 1GR-FE (for RHD) 
    Tester Connection
    Condition
    Specified Condition
    r3-2 - C34-27 (D)
    Always
    Below 1 Ω
    r3-2 - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (for LHD) 
    Tester Connection
    Condition
    Specified Condition
    A43-2 - C91-15 (CLSW)
    Always
    Below 1 Ω
    A43-2 - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (for RHD) 
    Tester Connection
    Condition
    Specified Condition
    r3-2 - C91-15 (CLSW)
    Always
    Below 1 Ω
    r3-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Clutch Switch Circuit (Aug 2013 – Jul 2014)Cruise Control Switch Circuit (Aug 2013 – Jul 2014) →