2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0571 Stop Light Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2013

DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. Upon receiving the signal, the ECM cancels cruise control. Even if there is a malfunction in the stop light signal circuit while cruise control is in operation, normal driving is maintained due to a fail-safe function.
When the brake pedal is depressed, positive voltage is applied to terminal STP of the ECM through the STOP fuse and stop light switch, and the ECM cancels cruise control.
DTC Code
DTC Detection Condition
Trouble Area
P0571
The voltages of terminals ST1- and STP of the ECM are both below 1 V for 0.5 seconds or more.
  1. Stop light switch circuit
  2. Stop light switch assembly
  3. ECM

WIRING DIAGRAM

E282944E08
E285068E02

INSPECTION PROCEDURE

NOTICE:
  1. When the ECM is replaced with a new one, initialization must be performed (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - BATTERY)

  1. E277387E09
    Disconnect the A85 switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A85-1 (B) - Body ground
    Always
    11 to 14 V
    A85-5 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A85-3 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
  1. Disconnect the A85 switch connector.

  1. Disconnect the G55*1 and G56*1 or G57*2 ECM connectors.

    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE 
    Tester Connection
    Switch Condition
    Specified Condition
    A85-4 (L) - G55-8 (ST1-)
    Always
    Below 1 Ω
    A85-2 (L) - G56-18 (STP)
    A85-4 (L) - Body ground
    Always
    10 kΩ or higher
    A85-2 (L) - Body ground
    for 1KD-FTV 
    Tester Connection
    Switch Condition
    Specified Condition
    A85-4 (L) - G57-9 (ST1-)
    Always
    Below 1 Ω
    A85-2 (L) - G57-8 (STP)
    A85-4 (L) - Body ground
    Always
    10 kΩ or higher
    A85-2 (L) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK STOP LIGHT SWITCH ASSEMBLY
  1. Temporarily replace the stop light switch with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

Result 
Result
Proceed to
OK
A
NG (for 1GR-FE)
B
NG (for 1KD-FTV)
C


B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

END (STOP LIGHT SWITCH IS DEFECTIVE)


← P0503 Vehicle Speed Sensor Circuit Malfunction (from Aug 2014)P0575 Cruise Control Input Circuit (Aug 2013 – Jul 2014) →