2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

TERMINALS OF ECU

System information · Vehicles built from Aug 2013


CHECK DRIVING SUPPORT ECU
E158948E05

NOTICE:
  1. As disconnecting the connector to perform inspections may cause DTCs to be stored, clear DTCs after performing inspections.
  2. As the connector may be damaged if a load of more than 10 kg (22 lb) is applied to it, do not apply any more load than necessary to the connector.

  1. Disconnect the G119 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G119-30 (B) - Body ground
    G - Body ground
    ECU power source circuit
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    G119-25 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the G119 ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G119-7 (MODE) - Body ground
    SB - Body ground
    Distance control switch signal
    Ignition switch ON, distance control switch off
    11 to 14 V
    Ignition switch ON, distance control switch on
    Below 1 V
    G119-32 (WIP2) - Body ground
    P - Body ground
    Windshield wiper switch circuit
    Ignition switch ON, windshield wiper switch Hi
    11 to 14 V
    Ignition switch ON, windshield wiper switch Lo
    Approximately 9 V
    Ignition switch ON, windshield wiper switch off
    Below 1 V
    If the result is not as specified, the ECU may be malfunctioning.


CHECK ECM (for 1GR-FE)
E195784E06
  1. Disconnect the C36, G55 and G56 ECM connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G55-24 (BATT) - Body ground
    L - Body ground
    Power source circuit
    Always
    11 to 14 V
    G56-21 (IGSW) - Body ground
    W - Body ground
    IG power source circuit
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    G55-8 (ST1-) - Body ground
    B - Body ground
    Stop light switch signal circuit
    Ignition switch ON, brake pedal released
    11 to 14 V
    Ignition switch ON, brake pedal depressed
    Below 1 V
    G56-18 (STP) - Body ground
    V - Body ground
    Stop light switch signal circuit
    Brake pedal depressed
    11 to 14 V
    Brake pedal released
    Below 1 V
    G56-11 (CCS) - Body ground
    B - Body ground
    Cruise control switch circuit
    Cruise control switch on
    Below 2.5 Ω
    Cruise control switch off
    1 MΩ or higher
    +RES switch held on
    235 to 245 Ω
    -SET switch held on
    617 to 643 Ω
    CANCEL switch held on
    1509 to 1571 Ω
    G56-17 (CCHG) - Body ground
    V - Body ground
    Cruise control switch circuit
    Cruise control switch on MODE switch held on
    Below 2.5 Ω
    Cruise control switch on MODE switch held off
    1 MΩ or higher
    C36-12 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the C36, G55 and G56 ECM connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G56-24 (S) - Body ground
    V - Body ground
    Transmission control switch circuit
    Ignition switch ON, shift lever in S
    11 to 14 V
    Ignition switch ON, shift lever not in S
    Below 1 V
    G56-16 (SFTU) - Body ground
    GR - Body ground
    Transmission control switch circuit
    Ignition switch ON, shift lever in S → shift lever moved to "+"
    11 to 14 V → Below 1 V
    G56-22 (SFTD) - Body ground
    LG - Body ground
    Transmission control switch circuit
    Ignition switch ON, shift lever in S → shift lever moved to "-"
    11 to 14 V → Below 1 V
    C34-27 (D) - Body ground
    B - Body ground
    Park/neutral position switch signal
    Ignition switch ON, shift lever in D
    11 to 14 V
    Ignition switch ON, shift lever not in D
    Below 1 V
    C34-35 (P) - Body ground
    L - Body ground
    Park/neutral position switch signal
    Ignition switch ON, shift lever in P
    11 to 14 V
    Ignition switch ON, shift lever not in P
    Below 1 V
    C34-28 (R) - Body ground
    R - Body ground
    Park/neutral position switch signal
    Ignition switch ON, shift lever in R
    11 to 14 V
    Ignition switch ON, shift lever not in R
    Below 1 V
    C34-29 (N) - Body ground
    G - Body ground
    Park/neutral position switch signal
    Ignition switch ON, shift lever in N
    11 to 14 V
    Ignition switch ON, shift lever not in N
    Below 1 V
    If the result is not as specified, the ECM may be malfunctioning.


CHECK ECM (for 1KD-FTV)
E195784E07
  1. Disconnect the C93, G57 and G58 ECM connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G57-23 (BATT) - Body ground
    L - Body ground
    Power source circuit
    Always
    11 to 14 V
    G58-24 (IGSW) - Body ground
    W - Body ground
    IG power source circuit
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    G57-9 (ST1-) - Body ground
    B - Body ground
    Stop light switch signal circuit
    Ignition switch ON, brake pedal released
    11 to 14 V
    Ignition switch ON, brake pedal depressed
    Below 1 V
    G57-8 (STP) - Body ground
    V - Body ground
    Stop light switch signal circuit
    Brake pedal depressed
    11 to 14 V
    Brake pedal released
    Below 1 V
    G57-14 (CCS) - Body ground
    B - Body ground
    Cruise control switch circuit
    Cruise control switch on
    Below 2.5 Ω
    Cruise control switch off
    1 MΩ or higher
    +RES switch held on
    235 to 245 Ω
    -SET switch held on
    617 to 643 Ω
    CANCEL switch held on
    1509 to 1571 Ω
    G58-9 (CCHG) - Body ground
    V - Body ground
    Cruise control switch circuit
    Cruise control switch on MODE switch held on
    Below 2.5 Ω
    Cruise control switch on MODE switch held off
    1 MΩ or higher
    C93-1 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK TRANSMISSION CONTROL ECU (for 1KD-FTV)
E200170E01
  1. Disconnect the G70 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G70-5 (BATT) - Body ground
    L - Body ground
    Power source circuit
    Always
    11 to 14 V
    G70-6 (IG2) - Body ground
    B - Body ground
    IG power source circuit
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the G70 ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G70-15 (S) - Body ground
    V - Body ground
    Transmission control switch circuit
    Ignition switch ON, shift lever in S
    11 to 14 V
    Ignition switch ON, shift lever not in S
    Below 1 V
    G70-22 (SFTU) - Body ground
    GR - Body ground
    Transmission control switch circuit
    Ignition switch ON, shift lever in S → shift lever moved to "+"
    11 to 14 V → Below 1 V
    G70-23 (SFTD) - Body ground
    LG - Body ground
    Transmission control switch circuit
    Ignition switch ON, shift lever in S → shift lever moved to "-"
    11 to 14 V → Below 1 V
    G71-8 (D) - Body ground
    B - Body ground
    Park/neutral position switch signal
    Ignition switch ON, shift lever in D
    11 to 14 V
    Ignition switch ON, shift lever not in D
    Below 1 V
    G69-13 (P) - Body ground
    L - Body ground
    Park/neutral position switch signal
    Ignition switch ON, shift lever in P
    11 to 14 V
    Ignition switch ON, shift lever not in P
    Below 1 V
    G71-9 (R) - Body ground
    R - Body ground
    Park/neutral position switch signal
    Ignition switch ON, shift lever in R
    11 to 14 V
    Ignition switch ON, shift lever not in R
    Below 1 V
    G69-14 (N) - Body ground
    G - Body ground
    Park/neutral position switch signal
    Ignition switch ON, shift lever in N
    11 to 14 V
    Ignition switch ON, shift lever not in N
    Below 1 V
    If the result is not as specified, the ECU may be malfunctioning.

← PROBLEM SYMPTOMS TABLE (from Aug 2014)DIAGNOSIS SYSTEM (from Aug 2013) →