ROAD TEST
Troubleshooting · Vehicles built from Aug 2013
- HINT:
- The dynamic radar cruise control system has 2 cruise control modes: constant speed control mode and vehicle-to-vehicle distance control mode.
- The vehicle-to-vehicle distance control mode is always selected when starting up the dynamic radar cruise control system.
- Operation of the constant speed control mode is the same as the conventional cruise control system.
- The vehicle-to-vehicle distance control mode is always selected when starting up the dynamic radar cruise control system.
| INSPECT SET SWITCH |
![]() ![]() |
Turn the cruise control switch on.
Check that the cruise control indicator light in the combination meter assembly illuminates.
Drive the vehicle at a desired speed (between 50 km/h and 170 km/h [30 mph and 105 mph]).
Push the cruise control switch to -SET.
Check that the cruise control SET indicator light in the combination meter assembly illuminates.
After releasing the switch, check that the vehicle cruises at the desired speed.
| INSPECT "+" SWITCH |
![]() ![]() |
Turn the cruise control switch on.
Drive the vehicle at a desired speed (between 50 km/h and 170 km/h [30 mph and 105 mph]).
Push the cruise control switch to -SET.
Check that vehicle speed increases while the cruise control switch is pushed to +RES, and that the vehicle cruises at the set speed when released.
Constant speed control mode:
Momentarily push the cruise control switch upward to +RES and immediately release it. Check that the vehicle speed increases by approximately 1.6 km/h (1 mph) (tap-up function).Vehicle-to-vehicle distance control mode (for Europe):
Momentarily push the cruise control switch upward to +RES and immediately release it. Check that the vehicle speed increases by approximately 5 km/h or 5 mph (tap-up function).Vehicle-to-vehicle distance control mode (except Europe):
Momentarily push the cruise control switch upward to +RES and immediately release it. Check that the vehicle speed increases by approximately 1 km/h or 1 mph (tap-up function).
| INSPECT "-" SWITCH |
![]() ![]() |
Turn the cruise control switch on.
Drive the vehicle at a desired speed (between 50 km/h and 170 km/h [30 mph and 105 mph]).
Push the cruise control switch to -SET.
Check that vehicle speed decreases while the cruise control switch is pressed down to -SET and that the vehicle cruises at the set speed when the cruise control switch is released.
Constant speed control mode:
Momentarily push the cruise control switch downward to -SET and immediately release it. Check that the vehicle speed decreases by approximately 1.6 km/h (1 mph) (tap-down function).Vehicle-to-vehicle distance control mode (for Europe):
Momentarily push the cruise control switch downward to -SET and immediately release it. Check that the vehicle speed decreases by approximately 5 km/h or 5 mph (tap-down function).Vehicle-to-vehicle distance control mode (except Europe):
Momentarily push the cruise control switch downward to -SET and immediately release it. Check that the vehicle speed decreases by approximately 1 km/h or 1 mph (tap-down function).
| INSPECT CANCEL FUNCTION (CANCEL SWITCH) |
![]() ![]() |
Turn the cruise control switch on.
Drive the vehicle at a desired speed (between 50 km/h and 170 km/h [30 mph and 105 mph]).
Push the cruise control switch to -SET.
When performing one of the following, check that the cruise control system is canceled and that the normal driving mode is set:
- Depressing the brake pedal
- Driving the vehicle while the vehicle stability control system is operating
- Moving the shift lever from D to N, or selecting 3rd, 2nd or 1st range with the shift lever in S
- When the ECM detects a cruise control cancel signal from the four wheel drive control ECU
- Pulling the cruise control switch to CANCEL
- Pushing the cruise control switch off
- Depressing the brake pedal
| INSPECT RES (RESUME) SWITCH |
![]() ![]() |
Turn the cruise control switch on.
Drive the vehicle at a desired speed (between 50 km/h and 170 km/h [30 mph and 105 mph]).
Push the cruise control switch to -SET.
Cancel the cruise control system by performing one of the following:
- Depressing the brake pedal
- Driving the vehicle while the vehicle stability control system is operating
- Moving the shift lever from D to N, or selecting 3rd, 2nd or 1st range with the shift lever in S
- When the ECM detects a cruise control cancel signal from the four wheel drive control ECU
- Pulling the cruise control switch to CANCEL
- Depressing the brake pedal
After the cruise control switch is pressed to +RES at a driving speed of more than 40 km/h (25 mph), check that the vehicle restores the speed set before cancellation.



