Downhill Assist Control Indicator Light does not Come ON
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Even if the downhill assist control switch is pressed, the downhill assist control indicator light blinks and downhill assist control does not activate under the following conditions:- The transfer is in H4.
- The brake system is malfunctioning.
- The temperature of the hydraulic brake booster increases and downhill assist control is temporarily canceled.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).
| 1. CHECK CAN COMMUNICATION LINE |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (for LHD: Click here, for RHD: Click here).
- OK:
- CAN Bus Check indicates no malfunctions in CAN communication.
Result Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | |
| 3. INSPECT DOWNHILL ASSIST CONTROL SWITCH |
Remove the downhill assist control switch (Click here).
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 4
Not pushed in
10 kΩ or higher
Pushed in
Below 1 Ω
Text in Illustration *a
Component without harness connected
(Downhill Assist Control Switch)
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID HDCS CIRCUIT) |
Disconnect the A7 skid control ECU (master cylinder solenoid) connector.
Disconnect the G158 downhill assist control switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A7-44 (HDCS) - G158-4
Always
Below 1 Ω
A7-44 (HDCS) or G158-4 - Body ground
Always
10 kΩ or higher
G158-1 - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOWNHILL ASSIST CONTROL LIGHT) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
Downhill Assist Control Light
Downhill assist control indicator light
Indicator light ON/OFF
Observe the combination meter.
When performing the Downhill Assist Control Light Active Test, check Downhill Assist Control Light in the Data List (Click here).
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Downhill Assist Control Light
Downhill assist control indicator light/ ON or OFF
ON: Indicator light on
OFF: Indicator light off
-
Result Result
Proceed to
Data List Display
Data List Display when Performing Active Test ON/OFF Operation
ON
Changes between ON and OFF
A
Does not change between ON and OFF (for LHD)
B
Does not change between ON and OFF (for RHD)
C
OFF
Changes between ON and OFF
A
Does not change between ON and OFF (for LHD)
B
Does not change between ON and OFF (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
