INSTALLATION
Removal / installation · Vehicles built from Aug 2013
| 1. INSTALL CONVERTER PROTECTOR STAY |
Install the 2 No. 1 converter protector stays and 2 No. 2 converter protector stays to the front exhaust pipe.
| 2. INSTALL MONOLITHIC CONVERTER PROTECTOR |
Install the upper monolithic converter protector and lower monolithic converter protector with the 4 bolts and 4 nuts.
- Torque:
- 11 N*m{ 107 kgf*cm , 8 ft.*lbf }
| 3. INSTALL EXHAUST PIPE CLAMP SUB-ASSEMBLY |
Install the exhaust pipe clamp with the bolt.
- Torque:
- 11 N*m{ 107 kgf*cm , 8 ft.*lbf }
| 4. INSTALL NO. 3 WIRING HARNESS CLAMP BRACKET |
Install the No. 3 wiring harness clamp bracket with the bolt.
- Torque:
- 18 N*m{ 184 kgf*cm , 13 ft.*lbf }
| 5. INSTALL NO. 3 EXHAUST GAS TEMPERATURE SENSOR |
![]() ![]() |
- NOTICE:
- If the sensor is dropped, replace it with a new one.
Using a 14 mm union nut wrench, install the No. 3 exhaust gas temperature sensor.
- Torque:
- 30 N*m{ 306 kgf*cm , 22 ft.*lbf }
Text in Illustration *1
Blue Tape
- NOTICE:
- Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).
- HINT:
- The identification tape on the exhaust gas temperature sensor is blue.
Attach the No. 3 exhaust gas temperature sensor wire harness.
| 6. INSTALL NO. 2 EXHAUST GAS TEMPERATURE SENSOR |
![]() ![]() |
- NOTICE:
- If the sensor is dropped, replace it with a new one.
Using a 14 mm union nut wrench, install the No. 2 exhaust gas temperature sensor.
- Torque:
- 30 N*m{ 306 kgf*cm , 22 ft.*lbf }
Text in Illustration *A
for Automatic Transmission
*B
for Manual Transmission
*1
Yellow Tape
*2
Red Tape
- NOTICE:
- Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).
- HINT:
- Refer to the illustration to identify the No. 2 exhaust gas temperature sensor being used.
| 7. INSTALL EXHAUST GAS TEMPERATURE SENSOR |
![]() ![]() |
- NOTICE:
- If the sensor is dropped, replace it with a new one.
Using a 14 mm union nut wrench, install the exhaust gas temperature sensor.
- Torque:
- 30 N*m{ 306 kgf*cm , 22 ft.*lbf }
Text in Illustration *1
Green Tape
- NOTICE:
- Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).
- HINT:
- The identification tape on the exhaust gas temperature sensor is green.
| 8. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Install a new gasket and the front exhaust pipe to the No. 2 turbine outlet elbow with 3 new nuts.
- Torque:
- 54 N*m{ 554 kgf*cm , 40 ft.*lbf }
Connect the front exhaust pipe to the 2 exhaust pipe supports.
- HINT:
- Install the exhaust pipe supports after installing the No. 3 frame crossmember.
Connect the No. 7 exhaust pipe air hose to the front exhaust pipe with a new clip.

Text in Illustration *a
Paint Mark
*b
Stopper
*c
Clip
*d
4 to 10 mm (0.157 to 0.394 in.)
- NOTICE:
- Align the paint marks of the front exhaust pipe and No. 7 exhaust pipe air hose and insert the No. 7 exhaust pipe air hose until it contacts the stopper.
- Make sure the clip is 4 to 10 mm (0.157 to 0.394 in.) from the end of the No. 7 exhaust pipe air hose when installing the clip.
- Make sure that there is no slack in the No. 7 exhaust pipe air hose, and that it is not twisted or bent.
- Take care not to damage the inner or outer surface of the No. 7 exhaust pipe air hose when installing it. If the No. 7 exhaust pipe air hose is damaged, replace it with a new one.
- Align the paint marks of the front exhaust pipe and No. 7 exhaust pipe air hose and insert the No. 7 exhaust pipe air hose until it contacts the stopper.
Connect the No. 6 exhaust pipe air hose to the front exhaust pipe with a new clip.

Text in Illustration *a
Paint Mark
*b
Stopper
*c
Clip
*d
4 to 10 mm (0.157 to 0.394 in.)
- NOTICE:
- Align the paint marks of the front exhaust pipe and No. 6 exhaust pipe air hose and insert the No. 6 exhaust pipe air hose until it contacts the stopper.
- Make sure the clip is 4 to 10 mm (0.157 to 0.394 in.) from the end of the exhaust pipe air hose when installing the clip.
- Make sure that there is no slack in the No. 6 exhaust pipe air hose, and that it is not twisted or bent.
- Take care not to damage the inner or outer surface of the No. 6 exhaust pipe air hose when installing it. If the No. 6 exhaust pipe air hose is damaged, replace it with a new one.
- Align the paint marks of the front exhaust pipe and No. 6 exhaust pipe air hose and insert the No. 6 exhaust pipe air hose until it contacts the stopper.
Connect the No. 3 exhaust gas temperature sensor connector.
Connect the No. 2 exhaust gas temperature sensor connector.
Connect the exhaust gas temperature sensor connector.
| 9. INSTALL AIR FUEL RATIO SENSOR |
Disconnect the air fuel ratio sensor connector and detach the clamp.

Using SST, remove the air fuel ratio sensor from the front exhaust pipe.

- SST
- 09224-00010
| 10. INSTALL NO. 3 EXHAUST PIPE SUPPORT BRACKET |
Install the No. 3 exhaust pipe support bracket with the 2 bolts.
- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
| 11. INSTALL NO. 2 EXHAUST PIPE SUPPORT BRACKET |
Install the No. 2 exhaust pipe support bracket with the 2 bolts.
- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
| 12. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY (for Manual Transmission) |
Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.
- Torque:
- 72 N*m{ 734 kgf*cm , 53 ft.*lbf }
Install the 4 bolts to the No. 3 frame crossmember sub-assembly.
- Torque:
- 30 N*m{ 306 kgf*cm , 22 ft.*lbf }
| 13. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY (for Automatic Transmission) |
Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.
- Torque:
- 30 N*m{ 306 kgf*cm , 22 ft.*lbf }
Install the frame crossmember with the 4 bolts and 4 nuts.
- Torque:
- 72 N*m{ 734 kgf*cm , 53 ft.*lbf }
| 14. INSTALL FRONT SUSPENSION MEMBER BRACKET LH AND RH (for Automatic Transmission) |
Install the front suspension member bracket LH and front suspension member bracket RH with the 8 bolts.
- Torque:
- 33 N*m{ 337 kgf*cm , 24 ft.*lbf }
| 15. INSTALL FRONT SUSPENSION MEMBER BRACKET RH (for Manual Transmission) |
Install the front suspension member bracket RH with the 4 bolts.
- Torque:
- 33 N*m{ 337 kgf*cm , 24 ft.*lbf }
| 16. INSTALL FRONT SUSPENSION MEMBER BRACKET LH (for Manual Transmission) |
Install the front suspension member bracket LH with the 4 bolts.
- Torque:
- 33 N*m{ 337 kgf*cm , 24 ft.*lbf }
| 17. INSTALL CENTER EXHAUST PIPE ASSEMBLY |
Using a vernier caliper, measure the free length of the compression spring.

- Minimum free length:
- 38.5 mm (1.52 in.)
- If the free length is less than the minimum, replace the compression spring.
Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the front exhaust pipe.

Text in Illustration *1
Gasket
*a
Wooden Block
- NOTICE:
- Be sure to install the gasket so that it faces the correct direction.
- Do not reuse the gasket.
- Do not damage the gasket.
- When connecting the exhaust pipe, do not push in the gasket with the exhaust pipe.
- Be sure to install the gasket so that it faces the correct direction.
for 3 Door:
Connect the center exhaust pipe to the 2 exhaust pipe supports.
for 5 Door:
Install the No. 1 exhaust pipe heat insulator with the nut.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
Install the exhaust pipe damper with the 2 bolts.
- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
Connect the center exhaust pipe to the 3 exhaust pipe supports.
Install the center exhaust pipe and 2 compression springs with the 2 bolts.
- Torque:
- 43 N*m{ 438 kgf*cm , 32 ft.*lbf }
| 18. INSTALL TAILPIPE ASSEMBLY |
Connect the tailpipe to the exhaust pipe support.
Install a new gasket to the center exhaust pipe.
Connect the tailpipe to the center exhaust pipe.
Install the 2 bolts.
- Torque:
- 48 N*m{ 489 kgf*cm , 35 ft.*lbf }
| 19. INSPECT FOR EXHAUST GAS LEAK |
- If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.



