2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCHARGE FUEL SYSTEM PRESSURE
  1. Discharge the fuel system pressure (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT BUMPER COVER LOWER
  1. Remove the clip, 5 bolts and front bumper cover lower.


4. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.

  1. A224743
    Unhook the engine under cover from the vehicle body as shown in the illustration.


5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


A273797E01
Text in Illustration 
*1
Reservoir Cap
*2
Radiator Cap
*3
Radiator Drain Cock Plug
*4
Cylinder Block Drain Cock Plug
  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the coolant from the engine.


6. REMOVE V-BANK COVER

  1. A229925E01
    Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Pin
    *2
    Hook


7. REMOVE NO. 1 AIR CLEANER HOSE

  1. A221455
    Disconnect the ventilation hose and vacuum hose.

  1. Detach the wire harness clamp.

  1. Remove the bolt and loosen the 2 hose clamps.

  1. Remove the No. 1 air cleaner hose.


8. REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)

  1. A221459
    for Bank 1 Side:
    Remove the bolt and disconnect the air tube assembly from the emission control valve set.

  1. A221458
    for Bank 2 Side:
    Remove the 2 bolts and disconnect the air tube assembly from the No. 2 emission control valve set.


9. REMOVE INTAKE AIR SURGE TANK

  1. A221456
    Disconnect the throttle body connector.

  1. Disconnect the No. 4 water by-pass hose.

  1. Disconnect the No. 5 water by-pass hose.

  1. A221457
    Disconnect the No. 1 fuel vapor feed hose.

  1. Disconnect the No. 1 vacuum switching valve connector.

  1. Disconnect the No. 1 ventilation hose.

  1. A221464
    Detach the 2 heater hose clamps.

  1. A221460
    Remove the 2 bolts and throttle body bracket.

  1. A221461
    Using a clip remover, detach the wire harness clamp.

  1. A221462
    Remove the 2 bolts and No. 1 surge tank stay.

  1. A221463
    Remove the 2 bolts and No. 2 surge tank stay.

  1. A221465
    Remove the 2 nuts, 4 bolts and intake air surge tank.

  1. Remove the gasket.


10. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A223037
    Disconnect the 6 fuel injector connectors.

  1. Remove the 4 bolts and fuel delivery pipe together with the 6 fuel injectors.

    NOTICE:
    Be careful not to drop the injectors when removing the fuel delivery pipe.


11. REMOVE INTAKE MANIFOLD

  1. A221466
    Remove the 4 nuts, 6 bolts and 2 gaskets.

← REMOVAL (Aug 2013 – Jul 2014)INSTALLATION (Aug 2013 – Jul 2014) →