2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE REAR SEAT ASSEMBLY LH
  1. for 60/40 Split Double-folding Seat Type LH Side:
    Remove the rear seat assembly LH (Click here).

  1. for 60/40 Split Slide Walk-in Seat Type LH Side:
    Remove the rear seat assembly LH (Click here).


3. REMOVE REAR FLOOR SERVICE HOLE COVER

  1. A220797
    Remove the 3 screws and rear floor service hole cover.

  1. A220803E01
    Disconnect the fuel pump and sender gauge connector.
    Text in Illustration 
    *A
    for Single Tank Type
    *B
    for Double Tank Type


4. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

  1. A220805
    Remove the 6 bolts and No. 1 fuel tank protector.

  1. A224491
    for Half Cover Type:
    Remove the 4 bolts and No. 1 fuel tank protector.


5. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)

A223261

6. DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)

A223105

7. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

A223101

8. DISCONNECT FUEL CUT OFF TUBE (for Single Tank Type)

A223106

9. DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Single Tank Type)

  1. A223262
    Disconnect the fuel tank breather tube (Click here).


10. DISCONNECT NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)

  1. A223102
    Disconnect the No. 4 fuel main tube and fuel suction tube (Click here).


11. DISCONNECT FUEL CUT OFF TUBE (for Double Tank Type)

  1. A223280
    Disconnect the fuel cut off tube (Click here).


12. DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

  1. A223281
    Disconnect the fuel return tube and No. 2 fuel main tube (Click here).


13. DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Double Tank Type)

  1. A223282
    Disconnect the fuel tank breather tube (Click here).


14. DISCONNECT FUEL TANK TO FILLER PIPE HOSE

  1. A220811
    Disconnect the fuel tank to filler pipe hose from the filler pipe.


15. REMOVE FUEL TANK SUB-ASSEMBLY
  1. Place a transmission jack under the fuel tank.

  1. A220832
    Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.

  1. Slowly lower the transmission jack slightly.


16. REMOVE FUEL TANK CUSHION

  1. A220812E01
    Remove the No. 1, No. 2 and No. 3 fuel tank cushions from the fuel tank.
    Text in Illustration 
    *1
    No. 1 Fuel Tank Cushion
    *2
    No. 2 Fuel Tank Cushion
    *3
    No. 3 Fuel Tank Cushion


17. REMOVE FUEL RETURN TUBE SUB-ASSEMBLY AND FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)

  1. A223107E01
    Remove the 2 fuel tube joint clips and pull out the fuel return tube and fuel tank main tube.
    Text in Illustration 
    *1
    Fuel Tube
    *2
    Fuel Tube Joint
    *3
    Fuel Tube Joint Clip
    *4
    O-Ring

    NOTICE:
    1. Remove any dirt and foreign matter on the fuel tube joint before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.

  1. A223110
    Remove the fuel return tube and fuel tank main tube from the fuel tank.


18. REMOVE NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)

  1. A223109E01
    Remove the 2 fuel tube joint clips and pull out the No. 4 fuel main tube and fuel suction tube.
    Text in Illustration 
    *1
    Fuel Tube
    *2
    Fuel Tube Joint
    *3
    Fuel Tube Joint Clip
    *4
    O-Ring

    NOTICE:
    1. Remove any dirt and foreign matter on the fuel tube joint before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.

  1. A223112
    Detach the clamp and remove the No. 4 fuel main tube from the fuel tank.

  1. Detach the clamp and remove the fuel suction tube from the fuel tank.


19. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY, FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

  1. A223241E01
    Remove the 3 fuel tube joint clips and pull out the fuel tank main tube, fuel return tube and No. 2 fuel main tube.
    Text in Illustration 
    *1
    Fuel Tube
    *2
    Fuel Tube Joint
    *3
    Fuel Tube Joint Clip
    *4
    O-Ring

    NOTICE:
    1. Remove any dirt and foreign matter on the fuel tube joint before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.

  1. A223243
    Detach the clamp and remove the No. 2 fuel main tube from the fuel tank.

  1. Detach the clamp and remove the fuel return tube from the fuel tank.

  1. Remove the fuel tank main tube from the fuel tank.


20. REMOVE FUEL TANK VENT TUBE ASSEMBLY (for Single Tank Type)

  1. A243483E01
    Set SST on the retainer.
    SST
    09808-14030  

    HINT:
    1. Engage the claws of SST securely with the retainer holes to secure SST.
    2. Install SST while pressing the claws of SST against the retainer (towards the center of SST).

  1. A243482E01
    Using SST, loosen the retainer.
    SST
    09808-14030  
    Text in Illustration 
    V100135
    Turn

    HINT:
    Fit the tips of SST onto the ribs of the retainer.

    NOTICE:
    1. When the retainer is loosened, be careful as the fuel tank vent tube will spring upward from the force of the spring.
    2. Remove any foreign matter around the fuel tank vent tube before this operation.

  1. Remove the retainer.

  1. Remove the fuel tank vent tube assembly from the fuel tank.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Remove the gasket from the fuel tank.


21. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for Double Tank Type)

  1. A243483E01
    Set SST on the retainer.
    SST
    09808-14030  

    HINT:
    1. Engage the claws of SST securely with the retainer holes to secure SST.
    2. Install SST while pressing the claws of SST against the retainer (towards the center of SST).

  1. A243482E01
    Using SST, loosen the retainer.
    SST
    09808-14030  
    Text in Illustration 
    V100135
    Turn

    HINT:
    Fit the tips of SST onto the ribs of the retainer.

    NOTICE:
    1. When the retainer is loosened, be careful as the fuel suction with pump and gauge tube will spring upward from the force of the spring.
    2. Remove any foreign matter around the fuel suction with pump and gauge tube before this operation.

  1. Remove the retainer.

  1. Remove the fuel suction with pump and gauge tube assembly from the fuel tank.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Remove the gasket from the fuel tank.


22. REMOVE NO. 3 FUEL TANK PROTECTOR

  1. A220823
    Remove the 2 bolts.

  1. Detach the 4 clamps and remove the No. 3 fuel tank protector.


23. REMOVE FUEL TANK TO FILLER PIPE HOSE

  1. A220822
    Remove the fuel tank to filler pipe hose from the fuel tank.

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →