2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. REMOVE REAR SEAT HEADREST ASSEMBLY
  1. Remove the headrest.


2. REMOVE CAP

  1. B240438
    Remove the 2 caps.


3. REMOVE REAR SEAT LOWER CUSHION HINGE COVER LH

  1. B237376
    Remove the 2 screws.

  1. Detach the 3 claws and remove the cover.


4. REMOVE REAR SEAT LOWER CUSHION HINGE COVER RH

  1. B238682E01
    Remove the 2 screws.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 claws and guide and remove the cover.


5. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH

B241710
  1. Using a T45 "TORX" socket wrench, remove the bolt and inner belt assembly.


6. REMOVE REAR NO. 1 SEAT CUSHION MOULDING

  1. B236519E01
    Using a clip remover, remove the 2 clips.

  1. Detach the 2 claws and 4 guides and remove the moulding.

    Text in Illustration 
    *1
    Guide


7. REMOVE SEAT CUSHION COVER WITH PAD

  1. B239926E01
    Open the 2 fasteners.
    Text in Illustration 
    *1
    Fastener

  1. B236671
    Using a clip remover, remove the 2 clips and open the under part of the seat cushion cover.

  1. B239928E01
    Detach the 2 hooks and remove the seat cushion cover with pad.
    Text in Illustration 
    *1
    Hook


8. REMOVE NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH

  1. B236523E01
    Detach the fastener.
    Text in Illustration 
    *1
    Fastener

  1. Remove the hog rings and seat cushion cover.


9. REMOVE REAR SEAT CUSHION INNER EDGE PROTECTOR LH

  1. B236571E01
    Cut off the tack pins and remove the edge protector from the seat cushion pad.
    Text in Illustration 
    *1
    Tack Pin


10. REMOVE REAR NO. 2 SEAT CUSHION MOULDING

  1. B237377
    Remove the 2 screws.

  1. Detach the 2 claws and remove the moulding.


11. REMOVE NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH
  1. Operate the rear No. 2 seat lock control lever and retract the seat cushion frame.

  1. B237378
    Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts and remove the seat cushion frame.


12. REMOVE 3RD SEAT LINK SUB-ASSEMBLY LH

  1. B237381E01
    Remove the 3 clips.

  1. Detach the 2 claws and 4 guides and remove the 3rd seat link.

    Text in Illustration 
    *1
    Guide


13. REMOVE REAR NO. 2 SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

  1. B237379E01
    Detach the clamp.
    Text in Illustration 
    *1
    Cable End
    *2
    Clamp

  1. Twist the cable end in the direction indicated by the arrow and disconnect the cable.

  1. B237380E01
    Remove the screw.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 guides and remove the lever.


14. REMOVE REAR SEAT LEG COVER LH

  1. B237382E01
    Remove the clip.
    Text in Illustration 
    *1
    Hook

  1. Detach the 3 hooks and 5 clips and remove the cover.


15. REMOVE REAR NO. 3 SEAT LEG COVER LH

  1. B239683
    Detach the 2 claws and remove the cover.


16. REMOVE REAR SEAT CUSHION INNER HINGE COVER LH

  1. B237383E01
    Remove the screw and clip.

  1. Detach the guide and remove the cover.

    Text in Illustration 
    *1
    Guide


17. REMOVE REAR SEAT CUSHION INNER HINGE COVER RH

  1. B237384E01
    Remove the screw and clip.

  1. Detach the guide and remove the cover.

    Text in Illustration 
    *1
    Guide


18. REMOVE REAR SEAT LOCK CONTROL CABLE LH

  1. B240106E01
    Detach the clamp.

  1. Twist the cable end in the direction indicated by the arrow and remove the cable.

    Text in Illustration 
    *1
    Clamp
    *2
    Cable End


19. REMOVE REAR NO. 1 SEATBACK LOCK STRIKER COVER

  1. B237521E01
    Using a screwdriver, detach the claw and guide and remove the cover.
    Text in Illustration 
    *1
    Guide
    *2
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.


20. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

  1. B237386E01
    Remove the 2 screws.

  1. Detach the guide and remove the lever.

  1. Detach the clamp.

  1. Twist the cable end in the direction indicated by the arrow and disconnect the cable.

    Text in Illustration 
    *1
    Clamp
    *2
    Cable End
    *3
    Guide


21. REMOVE ROPE HOOK ASSEMBLY

  1. B237387E01
    Using a screwdriver, detach the 2 claws and open the cover.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

  1. B237388
    Remove the bolt and rope hook.


22. REMOVE REAR NO. 2 SEATBACK LOCK STRIKER COVER

  1. B237395E01
    Using a screwdriver, detach the claw and guide and remove the cover.
    Text in Illustration 
    *1
    Guide
    *2
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.


23. REMOVE REAR SEAT LOCK RELEASE LEVER ASSEMBLY

  1. B237397E01
    Remove the 2 screws.

  1. Detach the hook and remove the lever.

    Text in Illustration 
    *1
    Hook

  1. B237396E01
    Detach the 2 clamps.

  1. Twist the 2 cable ends in the direction indicated by the arrow and disconnect the 2 cables.

    Text in Illustration 
    *1
    Cable End
    *2
    Clamp


24. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH

  1. B240430
    Detach the 7 clips and remove the board.


25. REMOVE REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY

  1. B237586
    Detach the 4 claws and remove the 2 headrest supports.


26. REMOVE SEATBACK COVER WITH PAD

  1. B237522E01
    Detach the hooks and remove the seatback cover with pad.
    Text in Illustration 
    *1
    Hook


27. REMOVE REAR NO. 3 SEATBACK COVER SUB-ASSEMBLY LH

  1. B240431
    Remove the hog rings and seatback cover.


28. REMOVE REAR NO. 2 SEATBACK EDGE PROTECTOR

  1. B236572E01
    Cut off the tack pins and remove the protector from the seatback pad.
    Text in Illustration 
    *1
    Tack Pin


29. REMOVE NO. 2 SEATBACK COVER

  1. B240757
    Detach the 2 claws and remove the cover.


30. REMOVE REAR NO. 3 SEAT INNER RECLINING COVER LH

  1. B240113
    Detach the 4 claws and remove the cover.


31. REMOVE REAR NO. 3 SEAT OUTER RECLINING COVER LH

  1. B237399E01
    Remove the screw.

  1. Detach the guide and 2 claws and remove the cover.

    Text in Illustration 
    *1
    Guide


32. REMOVE REAR NO. 2 SEAT INNER RECLINING COVER LH

  1. B238702
    Detach the 5 claws and remove the cover.


33. REMOVE REAR NO. 2 SEAT OUTER RECLINING COVER LH

  1. B237400E01
    Remove the screw.

  1. Detach the guide and 2 claws and remove the cover.

    Text in Illustration 
    *1
    Guide


34. REMOVE FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

  1. B237525E01
    Remove the clamp labeled B and detach the 2 labeled clamps A.

  1. Cut off the 2 cable ties.

  1. Twist the cable end in the direction indicated by the arrow and remove the cable.

    Text in Illustration 
    *1
    Clamp A
    *2
    Clamp B
    *3
    Cable Tie
    *4
    Cable End


35. REMOVE NO. 2 SEAT LOCK CABLE

  1. B237526E01
    Detach the clamp.

  1. Twist the cable end in the direction indicated by the arrow and remove the cable.

    Text in Illustration 
    *1
    Clamp
    *2
    Cable End


36. REMOVE NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH

  1. B240432
    Using a T45 "TORX" socket wrench, remove the 4 "TORX" bolts and frame.


37. REMOVE NO. 3 SEAT LEG ASSEMBLY LH

  1. B240439
    Remove the 4 clips and seat cushion under carpet LH from the No. 3 seat leg.


38. REMOVE NO. 2 SEAT LEG ASSEMBLY (for RH Side)

  1. B240440
    Remove the 4 clips and seat cushion under carpet RH from the No. 2 seat leg.

← REMOVAL (from Aug 2013)REASSEMBLY (from Aug 2013) →