2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

NOTICE:
  1. Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU (Click here).
    1. The fold seat control ECU is replaced with a new one.
    2. Initialization (initial position reset) of the fold seat control ECU is performed.
  1. Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU (Click here).
    1. The fold seat control ECU is exchanged with one from another vehicle.
    2. The seatback frame and seat leg are inspected.
    3. The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.
    4. The seatback frame or seat leg is replaced.
    5. The cable is disconnected from the battery while the seatback or seat cushion is operating.

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. REMOVE DECK BOARD ASSEMBLY
  1. Operate the No. 2 fold seat switch and fold down the 2 seatbacks.

  1. B236495
    Remove the 2 bolts.

  1. Detach the 4 clips and remove the deck board.


2. REMOVE REAR NO. 4 FLOOR BOARD

  1. B236502E01
    Using a moulding remover, detach the clip and 3 claws.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 guides and remove the floor board.


3. REMOVE REAR NO. 3 FLOOR BOARD (w/o Rear Air Conditioning System)

  1. B239971E01
    Using a moulding remover, detach the clip and 4 claws.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 guides and remove the floor board.


4. REMOVE REAR NO. 3 FLOOR BOARD (w/ Rear Air Conditioning System)

  1. B236503E01
    Using a moulding remover, detach the clip and 3 claws.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 guides and remove the floor board.


5. REMOVE REAR FLOOR MAT SUPPORT PLATE

  1. Remove the 3 bolts.

    B236501E01

    Text in Illustration 
    *1
    Guide
    -
    -

  1. Detach the 4 claws and 2 guides.

  1. Detach the 5 clips and remove the support plate.


6. REMOVE DECK BOARD BRACKET REINFORCEMENT

  1. B236496E01
    Remove the 2 bolts.
    Text in Illustration 
    *1
    Hook

  1. Detach the 2 hooks and reinforcement.


7. REMOVE NO. 1 DECK BOARD BRACKET LH

  1. B236497
    Remove the 2 bolts and bracket.


8. REMOVE REAR NO. 2 SEAT ASSEMBLY LH
  1. Operate the No. 2 fold seat switch and raise the 2 seatbacks.

  1. B236504
    Disconnect the connector.

  1. B236506
    Remove the 2 bolts.

  1. B238648E01
    Using a screwdriver, detach the 2 guides and 6 claws and open the 2 covers.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape
    *2
    Guide

  1. B236494
    Remove the 2 bolts.

  1. B236507
    Remove the rear No. 2 seat assembly from the vehicle.

    NOTICE:
    Be careful not to damage the vehicle body.

    HINT:
    If removing the seat on the RH side with the LH side installed, remove it with the No. 3 rear seat leg cover LH raised as shown in the illustration.

← COMPONENTS (from Aug 2013)DISASSEMBLY (from Aug 2013) →