2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

NOTICE:
  1. Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU (Click here).
    1. The fold seat control ECU is replaced with a new one.
    2. Initialization (initial position reset) of the fold seat control ECU is performed.
  1. Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU (Click here).
    1. The fold seat control ECU is exchanged with one from another vehicle.
    2. The seatback frame and seat leg are inspected.
    3. The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.
    4. The seatback frame or seat leg is replaced.
    5. The cable is disconnected from the battery while the seatback or seat cushion is operating.

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. REMOVE CAP

  1. B239512
    Remove the 2 caps.


2. REMOVE REAR SEAT CUSHION LOWER HINGE COVER LH

  1. B238683
    Remove the 2 screws.

  1. Detach the 3 claws and remove the cover.


3. REMOVE REAR SEAT CUSHION LOWER HINGE COVER RH

  1. B238682E01
    Remove the 2 screws.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 claws and guide and remove the cover.


4. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH

B241710
  1. Using a T45 "TORX" socket wrench, remove the bolt and inner belt assembly.


5. REMOVE FOLD SEAT CONTROL ECU

  1. B236510
    Disconnect the 2 connectors.

  1. Remove the 2 nuts and ECU.


6. REMOVE REAR SEAT NO. 1 CUSHION MOULDING

  1. B236519E01
    Using a clip remover, remove the 2 clips.

  1. Detach the 2 claws and 4 guides and remove the moulding.

    Text in Illustration 
    *1
    Guide


7. REMOVE SEAT CUSHION COVER WITH PAD

  1. B238685E01
    Open the 2 fasteners.
    Text in Illustration 
    *1
    Fastener

  1. B236671
    Remove the 2 clips and open the under part of the seat cushion cover.

  1. B238687E01
    Detach the 2 hooks and remove the seat cushion cover with pad.
    Text in Illustration 
    *1
    Hook


8. REMOVE NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH

  1. B236523E01
    Detach the fastener.
    Text in Illustration 
    *1
    Fastener

  1. Remove the hog rings and seat cushion cover.


9. REMOVE REAR SEAT CUSHION INNER EDGE PROTECTOR LH

  1. B236571E01
    Cut off the tack pins and remove the protector from the cushion pad.
    Text in Illustration 
    *1
    Tack Pin


10. REMOVE REAR SEAT NO. 2 CUSHION MOULDING

  1. B238689
    Remove the 2 screws.

  1. Detach the 2 claws and remove the moulding.


11. REMOVE REAR SEAT NO. 3 LEG COVER LH

  1. B239683
    Detach the 2 claws and remove the cover.


12. REMOVE REAR SEAT CUSHION INNER HINGE COVER LH

  1. B238693E01
    Remove the screw and clip.
    Text in Illustration 
    *1
    Guide

  1. Detach the guide and remove the cover.


13. REMOVE REAR SEAT CUSHION INNER HINGE COVER RH

  1. B238692E01
    Remove the screw and clip.
    Text in Illustration 
    *1
    Guide

  1. Detach the guide and remove the cover.


14. REMOVE LOWER SEAT TRACK RAIL LH

  1. B238694
    Remove the 2 bolts and seat track rail.


15. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH

  1. B238695
    Detach the 7 clips and remove the board.


16. REMOVE REAR SEATBACK LOCK HOOK

  1. B238697
    Remove the lock hook.


17. REMOVE REAR SEAT NO. 1 COVER BEZEL

  1. B238696E01
    Remove the 2 screws, detach the guide and remove the bezel.
    Text in Illustration 
    *1
    Guide


18. REMOVE SEATBACK COVER WITH PAD

  1. B238698E01
    Detach the hooks.
    Text in Illustration 
    *1
    Hook

  1. B238699
    Detach the 8 clips and remove the seatback cover with pad.


19. REMOVE NO. 3 SEATBACK COVER SUB-ASSEMBLY LH

  1. B236581
    Remove the hog rings and seatback cover.


20. REMOVE REAR NO. 2 SEATBACK EDGE PROTECTOR

  1. B236572E01
    Cut off the tack pins and remove the protector from the seatback pad.
    Text in Illustration 
    *1
    Tack Pin


21. REMOVE NO. 2 SEATBACK COVER

  1. B238700
    Detach the 2 claws and remove the cover.


22. REMOVE REAR SEAT HEADREST COVER

  1. B238701E01
    Remove the 2 screws.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 claws and guide and remove the cover.


23. REMOVE REAR SEAT HEADREST CABLE

  1. B236550E01
    Detach the 2 clamps.
    Text in Illustration 
    *1
    Cable End
    *2
    Clamp

  1. Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.


24. REMOVE REAR SEAT HEADREST ASSEMBLY

  1. B238706
    Remove the 3 nuts and headrest.


25. REMOVE REAR SEATBACK EDGE PROTECTOR

  1. B236541
    Detach the 4 claws and remove the 2 protectors.


26. REMOVE REAR NO. 3 SEAT INNER RECLINING COVER LH

  1. B238704
    Detach the 4 claws and remove the cover.


27. REMOVE REAR NO. 3 SEAT OUTER RECLINING COVER LH

  1. B238705E01
    Remove the screw.
    Text in Illustration 
    *1
    Guide

  1. Detach the guide and 2 claws and remove the cover.


28. REMOVE NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH

  1. B247971
    Remove the bolt and disconnect the wire harness.

  1. B247518
    Using a screwdriver, release the lock lever as shown in the illustration.

  1. B237378
    Retract the seat cushion frame.

  1. Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts and seat cushion frame.


29. REMOVE REAR SEAT LEG COVER LH

  1. B238690E01
    Remove the clip.
    Text in Illustration 
    *1
    Hook

  1. Detach the 3 hooks and 5 clips and remove the cover.


30. REMOVE 3RD SEAT LINK SUB-ASSEMBLY LH

  1. B238691E01
    Remove the 3 clips.
    Text in Illustration 
    *1
    Guide

  1. Detach the 2 claws and 4 guides and remove the 3rd seat link.


31. REMOVE REAR NO. 2 SEAT INNER RECLINING COVER LH

  1. B238702
    Detach the 5 claws and remove the cover.


32. REMOVE REAR NO. 2 SEAT OUTER RECLINING COVER LH

  1. B238703E01
    Remove the screw.
    Text in Illustration 
    *1
    Guide

  1. Detach the guide and 2 claws and remove the cover.


33. REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY LH

  1. B236547E01
    Detach the 2 clamps.
    Text in Illustration 
    *1
    Clamp
    *2
    Cable End

  1. Twist the cable end in the direction indicated by the arrow and remove the cable.


34. REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY RH (for RH Side)

  1. B236546E01
    Cut off the 2 cable ties and detach the 3 clamps.
    Text in Illustration 
    *1
    Cable Tie
    *2
    Clamp
    *3
    Cable End

  1. Twist the cable end in the direction indicated by the arrow and remove the cable.


35. REMOVE REAR SEAT LOCK CONTROL CABLE LH

  1. B236549E01
    Detach the 2 clamps.
    Text in Illustration 
    *1
    Cable End
    *2
    Clamp

  1. Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.


36. REMOVE REAR SEAT LOCK CONTROL CABLE RH (for RH Side)

  1. B236548E01
    Cut off the 2 cable ties and detach the 3 clamps.
    Text in Illustration 
    *1
    Cable Tie
    *2
    Clamp
    *3
    Cable End

  1. Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.


37. REMOVE NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH

  1. B238707
    Using a T45 "TORX" socket wrench, remove the 4 "TORX" bolts and frame.


38. REMOVE REAR NO. 2 SEAT WIRE LH

  1. B238708
    Disconnect the connector.

  1. Detach the wire harness clamps and remove the seat wire.


39. REMOVE NO. 3 SEAT LEG ASSEMBLY LH

  1. B238829
    Remove the 4 clips and seat cushion under carpet LH from the No. 3 seat leg.


40. REMOVE NO. 2 SEAT LEG ASSEMBLY (for RH Side)

  1. B236573
    Remove the 4 clips and seat cushion under carpet RH from the No. 2 seat leg.

← REMOVAL (from Aug 2013)INSPECTION (from Aug 2013) →