REASSEMBLY
Removal / installation · Vehicles built from Aug 2013
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- NOTICE:
- Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU (Click here).
- The fold seat control ECU is replaced with a new one.
- Initialization (initial position reset) of the fold seat control ECU is performed.
- Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU (Click here).
- Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU (Click here).
- The fold seat control ECU is exchanged with one from another vehicle.
- The seatback frame and seat leg are inspected.
- The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.
- The seatback frame or seat leg is replaced.
- The cable is disconnected from the battery while the seatback or seat cushion is operating.
- Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU (Click here).
- HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
- Use the same procedure for the RH and LH sides.
| 1. INSTALL NO. 3 SEAT LEG ASSEMBLY LH |
Attach the 4 clips to install the seat cushion under carpet LH to the No. 3 seat leg.
| 2. INSTALL NO. 2 SEAT LEG ASSEMBLY (for RH Side) |
Attach the 4 clips to install the seat cushion under carpet RH to the No. 2 seat leg.
| 3. INSTALL REAR NO. 2 SEAT WIRE LH |
Attach the wire harness clamps to install the seat wire.
Connect the connector.
| 4. INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH |
Using a T45 "TORX" socket wrench, install the seatback frame with the 4 "TORX" bolts.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
| 5. INSTALL REAR SEAT LOCK CONTROL CABLE LH |
Twist the 2 cable ends in the direction indicated by the arrow to connect them.

Text in Illustration *1
Cable End
*2
Clamp
Attach the 2 clamps to install the cable.
| 6. INSTALL REAR SEAT LOCK CONTROL CABLE RH (for RH Side) |
Twist the 2 cable ends in the direction indicated by the arrow to connect them.

Text in Illustration *1
Cable Tie
*2
Clamp
*3
Cable End
Attach the 3 clamps to install the cable.
Install 2 new cable ties.
| 7. INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY LH |
Twist the cable end in the direction indicated by the arrow to connect it.

Text in Illustration *1
Cable End
*2
Clamp
Attach the 2 clamps to install the cable.
| 8. INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY RH (for RH Side) |
Twist the cable end in the direction indicated by the arrow to connect it.

Text in Illustration *1
Cable Tie
*2
Clamp
*3
Cable End
Attach the 3 clamps to install the cable.
Install the 2 new cable ties.
| 9. INSTALL REAR NO. 2 SEAT OUTER RECLINING COVER LH |
Attach the 2 claws and guide to install the cover.
Install the screw.
| 10. INSTALL REAR NO. 2 SEAT INNER RECLINING COVER LH |
Attach the 5 claws to install the cover.
| 11. INSTALL 3RD SEAT LINK SUB-ASSEMBLY LH |
Attach the 4 guides and 2 claws to install the seat leg link.
Install the 3 clips.
| 12. INSTALL REAR SEAT LEG COVER LH |
Attach the 5 clips and 3 hooks, to install the cover.
Install the clip.
| 13. INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH |
Using a T40 "TORX" socket wrench, install the seat cushion frame with the 4 "TORX" bolts.
- Torque:
- 25 N*m{ 255 kgf*cm , 18 ft.*lbf }
Pull out the seat cushion frame.
Connect the wire harness with the bolt.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
| 14. INSTALL REAR NO. 3 SEAT OUTER RECLINING COVER LH |
Attach the 2 claws and guide to install the cover.
Install the screw.
| 15. INSTALL REAR NO. 3 SEAT INNER RECLINING COVER LH |
Attach the 4 claws to install the cover.
| 16. INSTALL REAR SEATBACK EDGE PROTECTOR |
Attach the 4 claws to install the 2 protectors.
| 17. INSTALL REAR SEAT HEADREST ASSEMBLY |
Install the headrest with the 3 nuts.
- Torque:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
| 18. INSTALL REAR SEAT HEADREST CABLE |
Twist the 2 cable ends in the direction indicated by the arrow to install them.

Text in Illustration *1
Cable End
*2
Clamp
Attach the 2 clamps to install the cable.
| 19. INSTALL REAR SEAT HEADREST COVER |
Attach the 2 claws and guide, to install the cover.
Install the 2 screws.
| 20. INSTALL NO. 2 SEATBACK COVER |
Attach the 2 claws to install the cover.
| 21. INSTALL REAR NO. 2 SEATBACK EDGE PROTECTOR |
Install the protector to the seatback pad with new tack pins.
| 22. INSTALL NO. 3 SEATBACK COVER SUB-ASSEMBLY LH |
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

Text in Illustration *1
Hog Ring Pliers
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
- Be careful not to damage the cover.
| 23. INSTALL SEATBACK COVER WITH PAD |
Attach the 8 clips.
Attach the hooks to install the seatback cover with pad.
| 24. INSTALL REAR SEAT NO. 1 COVER BEZEL |
Pass the strap through the bezel hole.
Attach the guide to install the bezel.
Install the 2 screws.
| 25. INSTALL REAR SEATBACK LOCK HOOK |
Install the lock hook.
| 26. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH |
Attach the 7 clips to install the board.
| 27. INSTALL LOWER SEAT TRACK RAIL LH |
Install the track rail with the 2 bolts.
- Torque:
- 41 N*m{ 418 kgf*cm , 30 ft.*lbf }
| 28. INSTALL REAR SEAT CUSHION INNER HINGE COVER RH |
Attach the guide to install the cover.
Install the clip and screw.
| 29. INSTALL REAR SEAT CUSHION INNER HINGE COVER LH |
Attach the guide to install the cover.
Install the clip and screw.
| 30. INSTALL REAR NO. 3 SEAT LEG COVER LH |
Attach the 2 claws to install the cover.
| 31. INSTALL REAR SEAT NO. 2 CUSHION MOULDING |
Attach the 2 claws to install the moulding.
Install the 2 screws.
| 32. INSTALL REAR SEAT CUSHION INNER EDGE PROTECTOR LH |
Install the protector to the seat cushion pad with new tack pins.
| 33. INSTALL NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

Text in Illustration *1
Fastener
*2
Hog Ring Pliers
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
- Be careful not to damage the cover.
Attach the fastener.
| 34. INSTALL SEAT CUSHION COVER WITH PAD |
Attach the 2 hooks to install the seat cushion cover with pad.
Attach the 2 hooks.
Attach the 2 hooks to close the cover.
Close the 2 fasteners.
Attach the 2 fasteners.
| 35. INSTALL REAR SEAT NO. 1 CUSHION MOULDING |
Attach the 4 guides and 2 claws to install the moulding.
Install the 2 clips.
| 36. INSTALL FOLD SEAT CONTROL ECU |
Install the ECU with the 2 nuts.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Connect the 2 connectors.
| 37. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH |
Using a T45 "TORX" socket wrench, install the inner belt assembly with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
| 38. INSTALL REAR SEAT CUSHION LOWER HINGE COVER RH |
Attach the 2 claws to install the cover.
Install the 2 screws.
| 39. INSTALL REAR SEAT CUSHION LOWER HINGE COVER LH |
Attach the guide and 2 claws to install the cover.
Install the 2 screws.
| 40. INSTALL CAP |
Install the 2 caps.
