2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT REAR POWER SEAT SWITCH (for LH Side)

  1. B239071E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (FWD) - 6 (E)
    UP switch pressed
    Below 1 Ω
    5 (BACK) - 6 (E)
    DOWN switch pressed

    If the result is not as specified, replace the rear power seat switch assembly.
    Text in Illustration 
    *1
    UP Switch
    *2
    DOWN Switch
    *a
    Component without harness connected
    (Rear Power Seat Switch Assembly)

  1. B239073E01
    Apply battery voltage to the switch connector and check that the power seat switch illuminates.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 7 (ILL+)
    Battery negative (-) → 2 (ILL-)
    Illumination illuminates

    If the result is not as specified, replace the rear power seat switch assembly.
    Text in Illustration 
    *a
    Component without harness connected
    (Rear Power Seat Switch Assembly)


INSPECT REAR POWER SEAT SWITCH (for RH Side)

  1. B239071E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (FWD) - 6 (E)
    UP switch pressed
    Below 1 Ω
    5 (BACK) - 6 (E)
    DOWN switch pressed

    If the result is not as specified, replace the rear power seat switch assembly.
    Text in Illustration 
    *1
    UP Switch
    *2
    DOWN Switch
    *a
    Component without harness connected
    (Rear Power Seat Switch Assembly)

  1. B239073E01
    Apply battery voltage to the switch connector and check that the power seat switch illuminates.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 7 (ILL+)
    Battery negative (-) → 2 (ILL-)
    Illumination illuminates

    If the result is not as specified, replace the rear power seat switch assembly.
    Text in Illustration 
    *a
    Component without harness connected
    (Rear Power Seat Switch Assembly)


INSPECT NO. 1 FOLD SEAT SWITCH ASSEMBLY

  1. B239264E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (RTNL) - 7 (E)
    RETURN LH switch pressed
    Below 1 Ω
    6 (FLDL) - 7 (E)
    FOLD LH switch pressed
    3 (RTNR) - 7 (E)
    RETURN RH switch pressed
    8 (FLDR) - 7 (E)
    FOLD RH switch pressed

    If the result is not as specified, replace the No. 1 fold seat switch assembly.
    Text in Illustration 
    *1
    RETURN RH Switch
    *2
    FOLD RH Switch
    *3
    RETURN LH Switch
    *4
    FOLD LH Switch
    *a
    Component without harness connected
    (No. 1 Fold Seat Switch Assembly)

  1. B239265E01
    Apply battery voltage to the switch connector and check that the fold seat switch illuminates.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 5 (+B)
    Battery negative (-) → 7 (E)
    Illumination illuminates

    If the result is not as specified, replace the No. 1 fold seat switch assembly.
    Text in Illustration 
    *a
    Component without harness connected
    (No. 1 Fold Seat Switch Assembly)

← REMOVAL (from Aug 2013)INSTALLATION (from Aug 2013) →