2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0416 Secondary Air Injection System Switching Valve "B" Circuit Open

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The ECM operates the air injection VSV relay (AI-VSV) which causes the No. 2 emission control valve set to operate.
DTC No.
DTC Detection Condition
Trouble Area
P0416
Open or short in the air injection VSV relay (AI-VSV) circuit for 3 seconds (1 trip detection logic).
  1. Open or short in air injection VSV relay (AI-VSV) circuit
  2. Air injection VSV relay (AI-VSV)
  3. ECM
P0417
Open or short in the air injection VSV relay (AI-VSV) circuit for 3 seconds (1 trip detection logic).
  1. Open or short in air injection VSV relay (AI-VSV) circuit
  2. Air injection VSV relay (AI-VSV)
  3. ECM

WIRING DIAGRAM

A227240E04

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT AIR INJECTION VSV RELAY (AI-VSV)
  1. Inspect the air injection VSV relay (AI-VSV) (Click here).



NG
REPLACE AIR INJECTION VSV RELAY (AI-VSV)
OK


2. CHECK AIR INJECTION VSV RELAY (AI-VSV) (POWER SOURCE)
  1. Remove the air injection VSV relay (AI-VSV).

  1. A227244E01
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Air injection VSV relay (AI-VSV) terminal 1 - Body ground
    Ignition switch ON
    11 to 14 V
    Air injection VSV relay (AI-VSV) terminal 5 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    Air Injection VSV Relay (AI-VSV)

  1. Reinstall the air injection VSV relay (AI-VSV).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION VSV RELAY (AI-VSV))
  1. Remove the air injection VSV relay (AI-VSV).

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Air injection VSV relay (AI-VSV) terminal 2 - C36-21 (AIR1)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    Air injection VSV relay (AI-VSV) terminal 2 or C36-21 (AIR1) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the air injection VSV relay (AI-VSV).

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0412 Secondary Air Injection System Switching Valve "A" Circuit (from Aug 2013)P0416 Secondary Air Injection System Switching Valve "B" Circuit Open (+ P0417) (from Aug 2014) →