ON-VEHICLE INSPECTION
Inspection · Vehicles built from Aug 2013
| INSPECT STARTER RELAY (ST) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage applied to terminals 1 and 2
Below 1 Ω
| INSPECT GLOW PLUG RELAY (GLOW) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage applied to terminals 1 and 2
Below 1 Ω
| INSPECT FUEL PUMP RELAY (FUEL PMP) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage applied to terminals 1 and 2
Below 1 Ω
| INSPECT NO. 1 INTEGRATION RELAY (IG2) |
Check the IG2 fuse.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
IG2 fuse
Always
Below 1 Ω
Check the IG2 relay.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
1C-1 - 1A-5
Battery voltage not applied to terminals 1A-1 and 1A-3
10 kΩ or higher
Battery voltage applied to terminals 1A-1 and 1A-3
Below 1 Ω
If the result is not as specified, replace the integration relay.Text in Illustration *a
Component without harness connected
(Integration Relay)
| INSPECT NO. 1 INTEGRATION RELAY (EFI) |
Check the EFI fuse.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
EFI fuse
Always
Below 1 Ω
Check the EFI relay.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
1C-1 - 1B-4
Battery voltage not applied to terminals 1B-2 and 1B-3
10 kΩ or higher
Battery voltage applied to terminals 1B-2 and 1B-3
Below 1 Ω
Text in Illustration *a
Component without harness connected
(Integration Relay)
| INSPECT NO. 1 INTEGRATION RELAY (EDU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
1B-8 - 1B-5
Battery voltage not applied to terminals 1B-7 and 1B-4
10 kΩ or higher
Battery voltage applied to terminals 1B-7 and 1B-4
Below 1 Ω
Text in Illustration *a
Component without harness connected
(Integration Relay)
| INSPECT MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK) |
- NOTICE:
- The ACC relay and IG1 No. 1 relay are built into the main body ECU (driver side junction block).
Inspect the ACC relay.
Measure the resistance according to the value(s) in the table below.


Text in Illustration *a
Component without harness connected
(Main Body ECU)
-
-
- Standard Resistance:
Tester Connection
Condition
Specified Condition
2D-17 - 2K-1
Battery voltage not applied to terminals 2A-48 and 2D-4
10 kΩ or higher
Battery voltage applied to terminals 2A-48 and 2D-4
Below 1 Ω
Inspect the IG1 No. 1 relay.
Measure the resistance according to the value(s) in the table below.


Text in Illustration *a
Component without harness connected
(Main Body ECU)
-
-
- Standard Resistance:
Tester Connection
Condition
Specified Condition
2A-31 - 2K-1
Battery voltage not applied to terminals 2A-52 and 2D-4
10 kΩ or higher
Battery voltage applied to terminals 2A-52 and 2D-4
Below 1 Ω
