2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT STARTER RELAY (ST)

  1. A092673E37
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT EDU RELAY (EDU)

  1. B060778E26
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT OIL PRESSURE SWITCHING VALVE RELAY (2ST OIL PRESS)

  1. B060778E26
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT NO. 1 INTEGRATION RELAY (IG2)
  1. Check the IG2 fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      IG2 fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the IG2 fuse.

  1. Check the IG2 relay.

    1. A225101E08
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1A-4
      Battery voltage not applied to terminals 1A-1 and 1A-3
      10 kΩ or higher
      Battery voltage applied to terminals 1A-1 and 1A-3
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (No. 1 Integration Relay)
      If the result is not as specified, replace the No. 1 integration relay.


INSPECT NO. 1 INTEGRATION RELAY (EFI)
  1. Check the EFI fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EFI fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the EFI fuse.

  1. Check the EFI relay.

    1. A225101E08
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-4
      Battery voltage not applied to terminals 1B-2 and 1B-3
      10 kΩ or higher
      Battery voltage applied to terminals 1B-2 and 1B-3
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (No. 1 Integration Relay)
      If the result is not as specified, replace the No. 1 integration relay.


INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN)
  1. Check the EFI MAIN fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the EFI MAIN fuse.

  1. Check the EFI MAIN relay.

    1. A225101E08
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-8
      Battery voltage not applied to terminals 1B-5 and 1B-7
      10 kΩ or higher
      Battery voltage applied to terminals 1B-5 and 1B-7
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (No. 1 Integration Relay)
      If the result is not as specified, replace the No. 1 integration relay.


INSPECT MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

NOTICE:
The ACC relay and IG1 No. 1 relay are built into the main body ECU (driver side junction block).

  1. Inspect the ACC relay.

    1. Measure the resistance according to the value(s) in the table below.

      A229542E01

      Text in Illustration 
      *a
      Component without harness connected
      (Main Body ECU)
      -
      -

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2D-17 - 2K-1
      Battery voltage not applied to terminals 2A-48 and 2D-4
      10 kΩ or higher
      Battery voltage applied to terminals 2A-48 and 2D-4
      Below 1 Ω

      If the result is not as specified, replace the main body ECU.

  1. Inspect the IG1 No. 1 relay.

    1. Measure the resistance according to the value(s) in the table below.

      A229542E01

      Text in Illustration 
      *a
      Component without harness connected
      (Main Body ECU)
      -
      -

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2A-31 - 2K-1
      Battery voltage not applied to terminals 2A-52 and 2D-4
      10 kΩ or higher
      Battery voltage applied to terminals 2A-52 and 2D-4
      Below 1 Ω

      If the result is not as specified, replace the main body ECU.

← INSTALLATION (from Aug 2013)ON-VEHICLE INSPECTION (from Aug 2013) →