2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

DISASSEMBLY

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the RH side.


1. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

B241192E01
  1. Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the handle.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


2. REMOVE FRONT SEAT CUSHION SHIELD RH

B241194
  1. Remove the screw.

  1. Using a moulding remover, detach the 5 claws and 2 clips.

  1. Detach the cable clamp and remove the cushion shield.


3. REMOVE FRONT SEAT INNER CUSHION SHIELD RH

B241195
  1. Using a moulding remover, detach the 5 claws and remove the cushion shield.


4. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH
  1. for Manual Seat, Power Seat 4 Way Seat Type:
    Disconnect the 2 connectors and detach the 3 clamps.

  1. for Power Seat 8 Way Seat Type:
    Disconnect the 2 connectors and detach the 6 clamps.

  1. Remove the nut and front seat inner belt assembly RH.


5. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

  1. B241196
    Remove the rubber band from the seat cushion spring.

  1. B242236
    w/ Seat Heater System:
    Disconnect the seat heater connector and detach the wire harness clamp.

  1. B241198E01
    w/ Front Seat Side Airbag:

    1. Detach the claw and disconnect the airbag connector.

    2. Detach the 4 airbag wire harness clamps.

    3. Detach the fastening tape and open the cover.

      Text in Illustration 
      *1
      Fastening Tape

    4. Disconnect the airbag wire harness.

  1. B241200
    Detach the hook.

  1. B241199
    Detach the cable clamp and disconnect the cable from the seatback.

  1. B241201
    Remove the 4 bolts and seatback assembly.


6. REMOVE CAP

B239234
  1. Remove the 2 caps.


7. REMOVE SEAT CUSHION COVER WITH PAD

  1. B241202
    Using a clip remover, remove the clip.

  1. B239243
    w/ Seat Heater System:
    Disconnect the seat heater connector and detach the 3 wire harness clamps.

  1. Detach the hooks.

  1. B239181
    Detach the claw and disconnect the connector.

  1. Remove the seat cushion cover with pad.


8. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER

B239182
  1. Remove the hog rings and seat cushion cover from the seat cushion pad.


9. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)

B239184E01
  1. Cut off the tack pins and remove the front seat cushion heater from the front seat cushion cover.

    Text in Illustration 
    *1
    Tack Pin


10. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR LH

B241203E01
  1. Remove the screw.

  1. Move the protector in the direction of the arrow to detach the hook and 2 guides and remove the protector.

    Text in Illustration 
    *1
    Hook
    *2
    Guide


11. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR RH

B241205E01
  1. Remove the screw.

  1. Using a clip remover, detach the clip.

  1. Move the protector in the direction of the arrow to detach the hook and guide and remove the protector.

    Text in Illustration 
    *1
    Hook
    *2
    Guide


12. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)

B239190
  1. Disconnect the connector.

  1. Detach the 2 clamps and remove the seat heater control.


13. REMOVE FRONT SEAT WIRE RH
  1. Remove the seat wire.


14. REMOVE RECLINING ADJUSTER INSIDE COVER LH

B239256
  1. Detach the guide.

  1. Move the cover in the direction of the arrow to remove it.


15. REMOVE RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedure described for the LH side.


16. REMOVE SEPARATE TYPE FRONT SEATBACK COVER

  1. B242237
    Remove the 3 hog rings.

  1. Open the 2 fasteners, and then open the seatback cover.

    B242232E01

    Text in Illustration 
    *A
    for Cloth Seat
    *B
    for Leather Seat

  1. B239254
    w/ Front Seat Side Airbag:

    1. Remove the nut and seatback cover bracket from the seat frame.

    2. Disconnect the seatback cover bracket from the seatback pad.

  1. B239198
    Using a screwdriver, detach the 4 claws and remove the 2 headrest supports.

  1. Remove the hog rings and seatback cover.

    HINT:
    The number of hog rings differs according to seat type.


    B242230E01
    Text in Illustration 
    *A
    for Type A
    *B
    for Type B


17. REMOVE FRONT SEATBACK HEATER ASSEMBLY RH (w/ Seat Heater System)

  1. B239207E01
    Cut off the tack pins which fasten the seatback heater to the seatback cover, and then remove the seatback heater from the seatback cover.
    Text in Illustration 
    *1
    Tack Pin


18. REMOVE SEPARATE TYPE FRONT SEATBACK PAD
  1. Remove the seatback pad.


19. REMOVE FRONT SEAT CUSHION COVER RH

B241207
  1. Remove the screw and cover.


20. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH

B241208
  1. Remove the screw and cushion shield.


21. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)

CAUTION:
When storing the front seat side airbag assembly, keep the airbag deployment side facing upward.

HINT:
Use the same procedure for the RH and LH sides.

  1. B251815
    Detach the 2 clamps.

  1. B333276
    Remove the 2 nuts and front seat side airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

← REMOVAL (from Aug 2014)DISASSEMBLY (from Aug 2014) →