DISASSEMBLY
Removal / installation · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the RH side.
| 1.
REMOVE RECLINING ADJUSTER RELEASE HANDLE RH |
 |
Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the handle.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration
*1
|
Protective Tape
|
| 2.
REMOVE FRONT SEAT CUSHION SHIELD RH |
 |
Remove the screw.
Using a moulding remover, detach the 5 claws and 2 clips.
Detach the cable clamp and remove the cushion shield.
| 3.
REMOVE FRONT SEAT INNER CUSHION SHIELD RH |
 |
Using a moulding remover, detach the 5 claws and remove the cushion shield.
| 4.
REMOVE FRONT SEAT INNER BELT ASSEMBLY RH
|
 |
for Manual Seat, Power Seat 4 Way Seat Type:
Disconnect the 2 connectors and detach the 3 clamps.
for Power Seat 8 Way Seat Type:
Disconnect the 2 connectors and detach the 6 clamps.
Remove the nut and front seat inner belt assembly RH.
Remove the front seat belt anchor plate.
| 5.
REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
 |
- Remove the rubber band from the seat cushion spring.
- w/ Seat Heater System:
Disconnect the seat heater connector and detach the wire harness clamp.
- w/ Front Seat Side Airbag:
Detach the claw and disconnect the airbag connector.
Detach the 4 airbag wire harness clamps.
Detach the fastening tape and open the cover.
Text in Illustration
*1
|
Fastening Tape
|
Disconnect the airbag wire harness.
- Detach the hook.
- Detach the cable clamp and disconnect the cable from the seatback.
- Remove the 4 bolts and seatback assembly.
| 6.
REMOVE CAP |
 |
Remove the 2 caps.
| 7.
REMOVE SEAT CUSHION COVER WITH PAD |
 |
- Using a clip remover, remove the clip.
- w/ Seat Heater System:
Disconnect the seat heater connector and detach the 3 wire harness clamps.
Detach the hooks.
- Detach the claw and disconnect the connector.
Remove the seat cushion cover with pad.
| 8.
REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER |
 |
Remove the hog rings and seat cushion cover from the seat cushion pad.
| 9.
REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)
|
 |
Cut off the tack pins and remove the front seat cushion heater from the front seat cushion cover.
Text in Illustration
*1
|
Tack Pin
|
| 10.
REMOVE FRONT SEAT CUSHION EDGE PROTECTOR LH |
 |
Remove the screw.
Move the protector in the direction of the arrow to detach the hook and 2 guides and remove the protector.
Text in Illustration
*1
|
Hook
|
*2
|
Guide
|
| 11.
REMOVE FRONT SEAT CUSHION EDGE PROTECTOR RH |
 |
Remove the screw.
Using a clip remover, detach the clip.
Move the protector in the direction of the arrow to detach the hook and guide and remove the protector.
Text in Illustration
*1
|
Hook
|
*2
|
Guide
|
| 12.
REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)
|
 |
Disconnect the connector.
Detach the 2 clamps and remove the seat heater control.
| 13.
REMOVE FRONT SEAT WIRE RH |
 |
Remove the seat wire.
| 14.
REMOVE RECLINING ADJUSTER INSIDE COVER LH |
 |
Detach the guide.
Move the cover in the direction of the arrow to remove it.
| 15.
REMOVE RECLINING ADJUSTER INSIDE COVER RH |
 |
- HINT:
- Use the same procedure described for the LH side.
| 16.
REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
 |
- Remove the 3 hog rings.
Open the 2 fasteners, and then open the seatback cover.


Text in Illustration
*A
|
for Cloth Seat
|
*B
|
for Leather Seat
|
- w/ Front Seat Side Airbag:
Remove the nut and seatback cover bracket from the seat frame.
Disconnect the seatback cover bracket from the seatback pad.
- Using a screwdriver, detach the 4 claws and remove the 2 headrest supports.
Remove the hog rings and seatback cover.
- HINT:
- The number of hog rings differs according to seat type.


Text in Illustration
*A
|
for Type A
|
*B
|
for Type B
|
| 17.
REMOVE FRONT SEATBACK HEATER ASSEMBLY RH (w/ Seat Heater System)
|
 |
- Cut off the tack pins which fasten the seatback heater to the seatback cover, and then remove the seatback heater from the seatback cover.
Text in Illustration
*1
|
Tack Pin
|
| 18.
REMOVE SEPARATE TYPE FRONT SEATBACK PAD |
 |
Remove the seatback pad.
| 19.
REMOVE FRONT SEAT CUSHION COVER RH |
 |
Remove the screw and cover.
| 20.
REMOVE FRONT SEAT LOWER CUSHION SHIELD RH |
 |
Remove the screw and cushion shield.
| 21.
REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)
|
 |
- CAUTION:
- When storing the front seat side airbag assembly, keep the airbag deployment side facing upward.
- HINT:
- Use the same procedure for the RH and LH sides.
- Detach the 2 clamps.
- Remove the 2 nuts and front seat side airbag assembly.
- CAUTION:
- The nuts must not be reused.
- Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.