2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

DISASSEMBLY

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. REMOVE ROOF SIDE AIR OUTLET REGISTER (w/ Rear Air Conditioning System)

B182435

HINT:
Use the same procedure for all roof side air outlet registers.

  1. Detach 6 claws and remove the roof side air outlet register.


2. REMOVE NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)

B238788
  1. Remove the 2 No. 1 roof silencer pads.


3. REMOVE NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)

B238790
  1. Remove the No. 2 roof silencer pad.


4. REMOVE NO. 3 ROOF SILENCER PAD

B238792
  1. Remove the No. 3 roof silencer pad.


5. REMOVE NO. 4 ROOF SILENCER PAD (w/o Sliding Roof)

B238786
  1. Remove the No. 4 roof silencer pad.


6. REMOVE VANITY LIGHT ASSEMBLY LH

B175184E02
  1. Detach the 2 claws labeled A and separate the bulb holder from the vanity light as shown in the illustration.

  1. Detach the claw labeled B and remove the vanity light.

    Text in Illustration 
    *1
    Claw A
    *2
    Claw B
    *3
    Bulb Holder


7. REMOVE VANITY LIGHT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


8. REMOVE NO. 1 ROOF WIRE
  1. Turn the visor connectors approximately 90° clockwise and remove them from the roof headlining.

  1. Detach each clamp and remove the No. 1 roof wire.

  1. Remove any butyl tape remaining on the roof headlining.

    B362382E01

    Text in Illustration 
    *A
    w/o Sliding Roof
    *B
    w/ Sliding Roof
    *C
    w/ Rear Seat Entertainment System
    *D
    w/ Rain Sensor, for LHD
    *E
    w/ EC Mirror
    *F
    w/ Rain Sensor, for RHD
    *1
    Visor Connector
    -
    -


9. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY

  1. w/o Sliding Roof:

    B358776E01

    Text in Illustration 
    *A
    for Diversity
    *B
    for Diversity, w/ Digital Audio Broadcasting

    1. Detach the No. 2 antenna cord sub-assembly from the 6 clamps and the notch on the rear of the roof headlining assembly.

    2. for Diversity:
      Detach the No. 2 antenna cord sub-assembly from the 6 clamps and the 2 notches on the rear of the roof headlining assembly.

    3. for Diversity, w/ Digital Audio Broadcasting:
      Detach the No. 2 antenna cord sub-assembly from the 7 clamps and the 2 notches on the rear of the roof headlining assembly.

    4. Remove the No. 2 antenna cord sub-assembly from the roof headlining assembly.

    5. Remove the double-sided tape from the roof headlining assembly.

  1. w/ Sliding Roof:

    B358777E01

    Text in Illustration 
    *A
    for Diversity
    *B
    for Diversity, w/ Digital Audio Broadcasting

    1. Detach the No. 2 antenna cord sub-assembly from the 11 clamps and the notch on the rear of the roof headlining assembly.

    2. for Diversity:
      Detach the No. 2 antenna cord sub-assembly from the 11 clamps and the 2 notches on the rear of the roof headlining assembly.

    3. for Diversity, w/ Digital Audio Broadcasting:
      Detach the No. 2 antenna cord sub-assembly from the 12 clamps and the 2 notches on the rear of the roof headlining assembly.

    4. Remove the No. 2 antenna cord sub-assembly from the roof headlining assembly.

    5. Remove the double-sided tape from the roof headlining assembly.

← REMOVAL (from Aug 2014)DISASSEMBLY (from Aug 2014) →